Search results

  1. rolmops

    1958 seahorse 10 running hot

    I'm thinking that nothing was very wrong when you decided to service the water pump. So problems appearing after this service probably have to do with possible mistakes. I would not be amazed at all if it is just a matter of the key not installed on the driveshaft when setting the impeller in...
  2. rolmops

    Penn or Cannon?

    here is where it is
  3. rolmops

    Seeking Advice: Real-Time Bathymetry Solutions for a 25-Foot Boat

    I did something a bit comparable on Lake Ontario. With the help of a Lowrance depth map,and a Furuno 588 with an airmar 262 transducer. I pointed a camera at both the screens and taped the film. The end result was a narrow line with very precise depth reading and irregularities. I pinpointed the...
  4. rolmops

    Penn or Cannon?

    Thank you Dingbat for that info. My preference goes toward the Penn Fathom masters and what made me favor those is the circuit board. This is probably because I am a tinkerer. I managed to find the problem on one of the circuit boards and managed to fix it. Needless to say, I felt good about...
  5. rolmops

    Steering cable wont bend enough to come out of outboard

    It sounds to me that it is time for a new steering cable that has a more flexible setup. You might want to think about a hydraulic one instead of a wire cable. It is amazing how you can stuff those in impossible angles and they still work great
  6. rolmops

    Penn or Cannon?

    I have been servicing and fixing my downriggers over the past few days and at this point I have 6 good working ones. 2 Cannon mag15s and 4 Penn 825s. I rebuilt all the motors and everything works fine. I would like your ideas and preferences between Cannon and Penn and why you have...
  7. rolmops

    Fuel line upgrade

    It depends on how cold it gets in winter where you live. The cold will make the line brittle and the squeeze ball hard and useless, causing you to get stuck on the lake. I find that the grey lines get leaky at the connections and the cheap black ones do the same. This is one article where you...
  8. rolmops

    Anyone know the part number of this

    It is called : "The commander classic panel mount control bezel
  9. rolmops

    combining a tailfin/powertran with a power pro 3.

    You are right ,but in this case,the use of the feed is mostly in very short bursts to make small corrections. It is not meant to be a constant feed.
  10. rolmops

    Evinrude 115 fuel leak

    You can see in the picture that the zip tie above the fuel enrichener has popped off. That may be the source of your leak
  11. rolmops

    combining a tailfin/powertran with a power pro 3.

    I thought about that a lot. It would be that way if I would use a transformer. The overall amount of energy would be the same just dressed up in a different package. That's why I decided to go with an actuator speed controller. This does not increase the current. It limits the amount of energy...
  12. rolmops

    combining a tailfin/powertran with a power pro 3.

    So about a year ago I bought a tailfin remote control kicker steering setup and I was not overly happy with it because fine tuning the remote control speed was an issue and I still had to do the speed control from the front end of my Islander. So what to do? I bought a powerpro 3 remote control...
  13. rolmops

    Excessive smoking

    Smoke is usually a sign that the fuel/air mixture is a bit too rich. Is your choke hanging up maybe?
  14. rolmops

    Bravo 3 Engine Alignment

    The gimbal bearing is supposed to turn up, down and sideways. Often they seem to be stuck in one position which may not be the right angle. When you put the alignment bar in you should jiggle it around to make sure the gimbal is loose enough to make those movements before you try to shove it all...
  15. rolmops

    1977 55 HP Evinrude

    The float bowls being empty may be pointing to your problem. Quite possibly the fuel in there evaporated, leaving a thin layer of gunk and that gunk is very capable of clogging all the narrow passages. I would let the carbs soak in carburetor cleaner over night and then blow them out with...
  16. rolmops

    remote control tiller steering question.

    It seems that a transformer is not the ticket, but I found a DC speed controller for actuators and I'm going to try that. I hope it works.
  17. rolmops

    remote control tiller steering question.

    Here goes. I have a tailfin (powertran) remote control wireless steering setup and a powerpro 3 wireless speed control both for the same kicker. I need 2 remote control fobs to run this setup which I do not like very much. So I tried to hook the tailfin actuator into the powerpro 3 and now...
  18. rolmops

    Operators manual for 1957 Evinrude fastwin 18 hp model 15020?

    I would not touch a Clymer with a 3 yard pole, but in this case, the old Evinrude engines are so simple that usually one look at the pictures will already make things clear.
  19. rolmops

    Pumping out oil from dipstick

    I disagree with the idea of not using a plastic tube going through the dipstick tube . Simply because the dipstick tube does not go all the way down to the bottom of the oil pan and you will never get all the oil out without the plastic tube going all the way down to the bottom of that oil pan
  20. rolmops

    Merc 3.0 Overheating

    Your problem may be as simple as a thermostat not opening up when it should. Just for fun, remove the thermostat , run the engine and see what happens to the temperature
Top