Search results

  1. K

    Seawater Pickup

    1” NPT pipe is plenty enough water supply. 1/14” I.D. hose will fit over it. Consider that in the drive there is a much smaller pipe which will deliver enough water for a sea water cooled 5.7 But as we know will not cool a fresh water cooled V style engine.
  2. K

    Seawater Pickup

    I would only use the scoop style, it has a grill that will keep out debris.
  3. K

    Seawater Pickup

    It does not matter If you do not mind the extra “Rooster Comb”. They are all suitable for the job. They can also be mounted through and on the underside of the trim plane. I had a 24’ Campbell once that was set up that way.
  4. K

    Remove quadrant gear and Stern leg is stuck in down position

    When the drive is down does the steering go in both directions without a bind? Pump some grease into those fittings while the bolts are loose. I cannot imagine what would keep the drive from not being able to lift by hand with the quadrant gear removed.
  5. K

    Seawater Pickup

    Do not be afraid to go through the bottom with a valve. The one advantage is one less “rooster comb” behind the hull. The “Y” connection is a definite good move to keep the drive cool and also works with a flush out . Greco # TH 1000 Through hull 1” NPT pick up Groco # IBV 1000 valve The rest...
  6. K

    Remove quadrant gear and Stern leg is stuck in down position

    Remove the rubber bumpers and just loosen each of the mounting bolts 1 turn. There is no way the ball gears can restrict the drive from coming off. With the bolts loose you should be able to shake the drive enough to remove the quadrant gear.
  7. K

    Going To Replace Shift Shaft Seals on MC-1 Today...

    As Chris said that is the only way to remove it.
  8. K

    Time to reassemble

    If you watch the video that Achris has on adjusting the shift system that may be all you need .
  9. K

    1986 Volvo Penta B230 AQ125A engine wiring

    Be sure that both carburetor throttle plates are synchronized. They run terrible off idle if they are not set. Those carburetors are easy to clean and most times the gaskets are re usable.
  10. K

    1986 Volvo Penta B230 AQ125A engine wiring

    If you have 2 carburetors then you have a 145. At this point you need to rebuild/clean the carburetors. To help with starting look at the solenoid and you will see a un used spade connection on the port side, make up a #16 ga, wire from the spade to the + side of the coil. Bayliner/ Volvo 4...
  11. K

    Remove quadrant gear and Stern leg is stuck in down position

    No problem Southkogs, we are all trying to help Lovemy Seaswril out but nun of us being on the scene we are just giving suggestions to the best of our knowledge and experience. Another problem he is having is the tilt clutch holding. When they are in good condition I used to be able to check...
  12. K

    Remove quadrant gear and Stern leg is stuck in down position

    Please read line #5 in post #3. The drive is not binding in the pivot caps. Tilt motors that are weak will run with out a load. The only other thing that could cause the problem is a bad electrical connection, I have even had a fuse that was causing the problem, it was testing good but was...
  13. K

    Remove quadrant gear and Stern leg is stuck in down position

    According to post #3 the drive does in fact can be raised and lowered manually with the gear removed. If the boat was at my shop the tilt motor would have been changed by now. I wrestled with those things for over 30 years.
  14. K

    1988 GM 5.7 stalling when slowing down

    If everything else is not causing the problem what you are describing then it could be possible the rotor gets hot in the distributor and is going to ground. When the boat is coming off of plane it loads the ignition more than when it is on plane. Get an extra rotor and see if that helps.
  15. K

    Hydraulic hoes replacement

    Try to post pictures of what you are working on and what engine and drive you have.
  16. K

    Chrysler 300 Sterndrive Removal

    There is a pristine Chrysler 300 drive on display at the Wisconsin Automotive Museum in Hartford, Wisconsin along with some antique and prototype marine drive systems plus outboard motors.
  17. K

    If you need to replace your Cobra power steering actuator here are a few tips…

    It looks like it was a real PITA Lou. When I answered your question I could not remember if you had the later style that is all aluminum of the one you did have. A lot of times the steel cylinder gets a rust hole leak or one of the 2 lines between the valve and cylinder. I have that cotter...
  18. K

    Remove quadrant gear and Stern leg is stuck in down position

    The tilt motor is not that hard to remove. A 3/8” universal 1/2” socket with a extension and ratchet will do the job. Most likely the brushes in the motor are worn or burned along with the commutator on the armature. Unbolt the quadrant, lift the drive to the 1/2 way position and Re bolt the...
  19. K

    Remove quadrant gear and Stern leg is stuck in down position

    It can be done as long as the drive is in the full down position. If the drive is not all the way down you will wipe out the ball gears, the upper gear case and the intermediate housing. This all will happen if the ball gears wear out to the point where they “slip” over each other. When that...
  20. K

    AQ120B unknown part question

    It is a water jacket drain. When the barbed fitting is loosened the block will drain.
Top