Search results

  1. K

    Volvo Penta AQ140 water coming out of carbs.

    That engine must have broken the timing belt, otherwise it would have hydro locked and not turned over. 2X with Scott on the carburetors.
  2. K

    Volvo Penta AQ140 water coming out of carbs.

    If you reuse your twin carburetor on the 130 it should bring that engine up to the original engine’s power.
  3. K

    5.0GL - No Power at Coil

    Your alternator may have a stud marked “stator”. It is only hot when the engine is running, it should have 12 volts. If you have that setup connect the choke to that terminal. You do not want to use the circuit that powers the coil. Another way is with a electric fuel pump safety switch that...
  4. K

    Need to ID motor

    The other screw on the starboard side above the lower is just a vent as the housing gets filled from the lower drain hole and an indicator if the case was full. If you have a dip stick in the top of the exhaust housing cover then you can use it to gauge when there is enough oil in the gear...
  5. K

    Need to ID motor

    Starboard side of the gearcase.
  6. K

    Removed the Wrong Screw

    Remove the drive like Scott said then stand it upside down, you should be able to fish the piece of metal that the screw went into and reinstall the screw holding the plate in place. Worse case scenario with a service manual separate the upper from the lower if you cannot fish out the plate with...
  7. K

    Couple of questions

    Too bad you did not pressure test the engine before taking the heads off. For the time being take them to a machine shop and have them checked. One source for a complete package is the Copart Auction. They often have boats that were involved in accidents.
  8. K

    5.0GL - No Power at Coil

    Are you sure the choke is adjusted correctly? With the key off and a cold engine all that is needed is for the choke butterfly to be barely closed. Have you actually seen the choke be fully open within 2 minutes? Does the choke housing get warm to the touch? Otherwise you did a good job and...
  9. K

    Cracked upper unit housing at spanner nut

    The front of the drive shaft housing has to compress and seal the large “O” ring in the bell housing. If you could put the broken piece back in place with some sealer or weld it, it might work. Otherwise you will need another drive shaft housing.
  10. K

    Test stand running 70's 350 water hook up

    I would start with a small amount of water to get the thermostat to open quicker then just a little more so that steam starts coming out with the water. That way if there are any oil leaks they will show.
  11. K

    Bad 1970 Mercruiser Engine, Please tell me there is still hope.

    There has to be a few marine salvage yards where you are located. I am sure one of them will be able to supply you with a good used set up. Go ahead and have the engine checked out, since it was used in fresh water there is a good chance it can be rebuilt. As far as hull repair and you are not...
  12. K

    Remove quadrant gear and Stern leg is stuck in down position

    When lowering the drive do not hold the tilt switch down until the drive hits the end of travel. Just tap the switch a few times until it is full down, if the drive comes down too fast it is possible to either wring off the end of either the tilt motor shaft, the tilt shaft or shear off the...
  13. K

    Water when pulling stern drive

    Rick explained the purpose of the ring. The main thing to prevent the ring from being damaged is to glue the ring in place and give the glue time to set. Trying to hold the drive up has a very good chance to tear the ring. Always have the drive supported at the same level as the bell housing...
  14. K

    Need to ID motor

    The last gray painted OMC engine was in 72. If the wrong oil without the additive has been used it may be possible the camshaft is going away. If you do remove the valve covers pay close attention that each rocker arm moves the same amount. The one advantage that the high profile drives have...
  15. K

    Seawater Pickup

    From the rear view it looks like you can spread the roller mount brackets enough to give enough clearance for the through hull fitting.
  16. K

    5.0GL - No Power at Coil

    The picture #355 is a Prestolite, does it have points and condenser or is it electronic? Volvo used Prestolite on all their “V” style engines. They phased in the electronic version in the 80s and used the same body. If there is only 1 wire going into the distributor then it is a breaker point...
  17. K

    5.0GL - No Power at Coil

    Try to post a picture of the distributor
  18. K

    Seawater Pickup

    If there is a Home Depot/ Lowes in your area they will have everything that you need in bronze. The clear hose with the cord inside is good enough. That is where I found what I needed for my Donzi for the final connections.
  19. K

    5.0GL - No Power at Coil

    Did you replace the accelerator diaphragm when you rebuilt the carburetor? Maybe I read something wrong and you did. Depending on the amount of ethanol is in your local gas supply can have a effect on the diaphragm and make stiff and will not supply enough gas when you move the throttle. If...
  20. K

    AQ271c overheating

    There is something else worth looking at, there is a metered orifice in the thermostat housing which is the bypass when the thermostat is closed. Sometimes they are so blocked up that you cannot see it. If you have a blasting cabinet would be good. The earlier Volvo power steering coolers had...
Top