Search results

  1. jerryjerry05

    120HP Force being smothered on exhaust fumes at idle

    On the diagram #13 is a screw?
  2. jerryjerry05

    Help!! 15hp Montgomery Ward Sea King by Chrysler Propeller

    Michigan Propeller. Solas propellers
  3. jerryjerry05

    Starter and choke issue

    Did you take it apart and clean the slide and hole where the slide goes? Out of adjustment. even a little can stop it from working.
  4. jerryjerry05

    Help!! 15hp Montgomery Ward Sea King by Chrysler Propeller

    Most marinas and boat parts places have access to a propeller repair shop.
  5. jerryjerry05

    Serial Number - Force 70HP

    Pics are part#s for the item shown. Did the boat and motor come as a package? Contact the manufacturer and see if they have the info? Give them the hull ID#
  6. jerryjerry05

    Tips and advice for repairing outboard head gasket

    Just put it on a piece of glass and see how big the gaps are? Never saw one so bad it couldn't be used.
  7. jerryjerry05

    120HP Force being smothered on exhaust fumes at idle

    That pic is where the motor gets it's air. And it's missing the cover, that shouldn't cause it to smoke so much it kills the motor. A motor that's being worked on will smoke a lot more because of the flooding effect of trying to start the motor frequently and not getting it hot enough to burn...
  8. jerryjerry05

    Starter and choke issue

    10v when it's disconnected or hooked to the solenoid?
  9. jerryjerry05

    Need Help Please 85hp Force Tilt Motor collapses under load

    All thread 1/2" with locking nuts on both ends.
  10. jerryjerry05

    Need some way of identifying model # for a 1990 Force 90HP

    IF?? the boat/motor was sold as a package deal boat/motor/trailer then someone(Tracker/Spectrum) should have the model/serial #??? maybe??
  11. jerryjerry05

    Need Help Please 85hp Force Tilt Motor collapses under load

    Bottom of both sides of the transom clamp, there's holes that you can put a 1/2"X12-14"bolt that the motor can rest on as you go.
  12. jerryjerry05

    Help motor only running on primer!!

    Your primer might be bad? Once it feeds then it should just stand by as the pump feeds the carb??
  13. jerryjerry05

    120HP Force being smothered on exhaust fumes at idle

    #17 probably wasn't the culprit?? Right where #1 is on the picture, that's where a gasket goes and it can cause your problem. Look for the powerhead parts breakdown.
  14. jerryjerry05

    Need some way of identifying model # for a 1990 Force 90HP

    Bluefin is/was a Spectrum product(I think) send the hull ID# to them and they can give you all the info for the motor that was sent out with the boat. Under the bottom carb on the intake is a foundry stamp. Also under the packs/coils on the block is another foundry stamp. Won't give the...
  15. jerryjerry05

    Starter and choke issue

    Choke's grounded through the bracket. Volt meter: unhook green choke wire from choke body, hook test lead to the green choke wire. Hit the choke/key, what's the voltage? Should be battery voltage, then when hooked back up, hit key again and read voltage. Post the results?? Not very often(1 in...
  16. jerryjerry05

    Blue/green substance leaking from L/U

    The allen head set screw is the drain plug. Sometimes they get stuck, I use a propane torch for a few seconds to help loosen it. You can't hurt it with the propane torch, acetylene is another thing.
  17. jerryjerry05

    Need Help Please 85hp Force Tilt Motor collapses under load

    Someone's messed with your T@T and removed the trim parts. The pic shows a trim actuator for a 50hp. the one for your motor is bigger. The two pieces together work in conjunction with each other. The other pic shows the 2 pieces together(50hp.)
  18. jerryjerry05

    Omc 5.7 ignition timing

    The car carb is probably sucking air someplace. Start it and spray starting fluid around the base. If the spray makes it run different? then it's sucking air.
  19. jerryjerry05

    Tilt trim switch wiring

    Those parts, keep a backup.
  20. jerryjerry05

    1988 Force 35hp backfired and wont run now

    One tiny backfire or cough can blow the diaphragm. Inspect.
Top