Search results

  1. jerryjerry05

    Part identification

    Not sure of the name?? It's part of the ignition system. If you change the stator the new system will take that part out. Sorry I can't give more info.
  2. jerryjerry05

    Need advise on bringing a 92 beretta succsess 200 back to life.

    To rebuild the upper gear case you will need special tools. You might be ok to just replace the bearing, You'll need to get the factory service manual to be sure.
  3. jerryjerry05

    55 hp Chrysler. Model 5551 has 3 piston rings

    Look on the block for a foundry stamp. Under the power pack , maybe the coils or on the bottom of the intake manifold? there might be a foundry stamp. Usually a circle with a smaller circle that has a number in it. That number is the year the foundry produced the block.
  4. jerryjerry05

    Sport Craft 232 and Outdrive Trim Problem

    If you run green to ground and blue to positive and swap them around, you should get some reaction from the electric motor. If not??? then I'd guess the motors bad???
  5. jerryjerry05

    55 hp Chrysler. Model 5551 has 3 piston rings

    What book? Clymer/Seloc ?? they're famous for not having the right info? Any more #s on the tag inside the bottom cowl? Your motor might be a 1969 model and the older ones used 3 rings.
  6. jerryjerry05

    Force 70Hp 1991 gear problem

    Line up neutral on both and that should work.
  7. jerryjerry05

    Force 70Hp 1991 gear problem

    Did you remove the screw on the side of the nose cone? There's a drain plug and then the gear shift arm pin. If you removed the pin??? then the lower probably needs to broken down and the shift assy. reassembled on the prop shaft. . Just changing the impeller shouldn't change the shift?? You...
  8. jerryjerry05

    Carter Fuel pump

    Put the following # into Google(fuel pump 3853970 rebuild kit) A bunch of pumps shows up, I think one might fit? Here's the part # but it's NLA FUEL PUMP 3853970
  9. jerryjerry05

    Volov penta Dp290 trim rams rebuild

    There used to be a guy on another site marineenginedotcom that was real good with Volvo repairs. His name might have been Rick.
  10. jerryjerry05

    Top piston worth replacing? (120hp low compression)

    From the new pics??? I'd find a machine shop that can do the bore/hone job. Then pull it apart. IF??? there's ANY damage to the piston skirts I'd change the piston. Post piston pics after cleaning/removal. If it really is a fresh water motor?? it should come apart fairly easy. I just rebuilt the...
  11. jerryjerry05

    Top piston worth replacing? (120hp low compression)

    IF??? you didn't destroy the gasket???? I'd try sealing with silicone and doing another comp test. Sounds like the gasket might have been the problem??? You can also pull the port covers and check the sides of the pistons for damage. The pistons can be replaced singly without breaking the...
  12. jerryjerry05

    Tilt Cylinders Leaking

    Post #68 he said it stopped leaking and still drifted down. That means the shuttle valve in the bottom of the pump needs new seals.
  13. jerryjerry05

    Cobra SX lower unit drain plug will not open

    Don't necessarily need an impact driver. A small propane torch and a BFS does the trick.
  14. jerryjerry05

    aq171

    This post was started in February last year. Then reopened by someone in June?
  15. jerryjerry05

    90 HP Force

    Pictures of the lower unit.
  16. jerryjerry05

    1989 force 85hp. model a? b? l?

    The difference on a model change can be as small as a screw or a tie/down. Very few big changes in the models?? If you get a service manual for 88/98/90 you should be close. The big changes were in the lower units.
  17. jerryjerry05

    Please help looking at a boat tomorrow

    ANYTHING but an OMC Cobra
  18. jerryjerry05

    '95 Force 120 - bottom cylinder not firing

    This works or one like it from Auto Zone
  19. jerryjerry05

    1964 45hp Sea King

    Sell it for parts if you can???? Or aluminum scrap?
  20. jerryjerry05

    Force piston rings

    The 87 35 was made in 6 different models, all 6 used the same ring set The parts are NLA from the factory but can be found if you look around, I found them on ebay, 114659905379 look up this part quick as it cheap and won't last long. There is a THEIF asking 75$ for a used set so be careful...
Top