Search results

  1. 87Starcraft

    1987 Starcraft islander 190v?

    Does anyone have pictures or methods on how they attached their sacrificial anodes?
  2. 87Starcraft

    1987 Starcraft islander 190v?

    I just didn’t have enough clamps. Trying to stay under budget. I do wish I bought more clamps and clamped together during the glue session
  3. 87Starcraft

    1987 Starcraft islander 190v?

    Gunnels trimmed out of the way
  4. 87Starcraft

    1987 Starcraft islander 190v?

    Dry fit the transom yesterday. Looks like I won’t be able to put epoxy and cloth on transom unless I cut a quarter inch off the stringers.
  5. 87Starcraft

    1987 Starcraft islander 190v?

    Thank you watermann
  6. 87Starcraft

    1987 Starcraft islander 190v?

    Progress? I should of clamped these pieces together... Thought the big tub of water was gonna be enough.
  7. 87Starcraft

    1987 Starcraft islander 190v?

    I think this is a question for watermann. I can’t figure out how to get the gunwhales off. The cabin sits directly on them.
  8. 87Starcraft

    1987 Starcraft islander 190v?

    Ten four I sure do appreciate ya
  9. 87Starcraft

    1987 Starcraft islander 190v?

    Wondering if my new one piece transom core will slide in like the three piece came out?
  10. 87Starcraft

    1987 Starcraft islander 190v?

    Thanks classic. I was gonna do that just a bit unsure if I could secure a patch like that but I found a post in your thread showing you did that
  11. 87Starcraft

    1987 Starcraft islander 190v?

    I’ve got a couple of patches and a bunch of jb backfill. I have all my aluminum stock, rivets, jb weld, and 5200. I also have the marine plywood and epoxy and 6 oz cloth from us composites. Trying to tackle corrosion then I will be doing glove it on All seems and reassembly. I really appreciate...
  12. 87Starcraft

    1987 Starcraft islander 190v?

    Also mine don’t sit on the ribs like yours do. My stringers have half circles in them going over each rib. I’m just gonna get an oversized stainless steel brush on a grinder and a dremel and try to tackle it that way. I just figured someone had a unique way of getting into that tight angle
  13. 87Starcraft

    1987 Starcraft islander 190v?

    Ate up*
  14. 87Starcraft

    1987 Starcraft islander 190v?

    So that’s not a good picture but the right side of the photo is the stringers and I was just stating my stringers are secured with solids. I was wondering if that was because it was an outboard and where the hull skin goes down at an angle and meets the stringers is very difficult to get a brush...
  15. 87Starcraft

    1987 Starcraft islander 190v?

    So. I don’t care about how the repair looks. But I do care about it never leaking again. And considering the transom is going to be against the transom skin I’m not sure if I can stick solids and that wood be up against the bucktails. Would placing these be a good alternative. maybe not...
  16. 87Starcraft

    1987 Starcraft islander 190v?

    This is the best forum for these aluminum boats.
  17. 87Starcraft

    1987 Starcraft islander 190v?

    My bad for not responding. The picture there are the stringers and they are secured to the hull skin under the middle rib sections. But not secured under the rib sections that run the width of the boat.secured with solids
  18. 87Starcraft

    1987 Starcraft islander 190v?

    How should I patch holes that are going to be directly behind the transom core? I found twenty holes 10 from trim tabs I do not want to put back on and the other ten from sheet metal screws 🤔
  19. 87Starcraft

    1987 Starcraft islander 190v?

    Found more corrosion. Got the outboard off .
  20. 87Starcraft

    1987 Starcraft islander 190v?

    I looked at the stringers today. My stringers are secured with solid rivets and run under each rib in the middle. This may be an outboard thing?
Top