Search results

  1. S

    Gas - Oil Mixture on old Evinrudes outboards

    If your just idling around just use very little oil (100 to 1) If you want to rip around use 16 to 1.... Otherwise use 0 to 1 and put them on the wall. Years of staring at them will do you wonders.
  2. S

    2007 e-tec 250 lower mount corrosion

    😆😆😆
  3. S

    2007 e-tec 250 lower mount corrosion

    If it fits??? Marry her?
  4. S

    Top speed??

    Aye yai yai, this website is still not perfect!!!
  5. S

    Gas lines

    He didn't mean old geezer....he ment it's going in the old freezer! When you were at Napa did you happen to pick up a filter? I strongly recommend it you may even want a gas mask.
  6. S

    Gas lines

    Type b uscg approved. 5/16. Or just rob a tube from your aquarium.....your choice.
  7. S

    tilt and trim rebuild 2000 50hp Johnson

    I think everything you learned was cheap.....cheapest education you will ever buy. As far as bleeding. Try doing it all after install and tell us which way you like. Might be another cheap education!
  8. S

    1993 60 evinrude missing above 3000 rpm once warm

    More info..... https://www.justanswer.com/boat/gvuyk-1994-evinrude-60-degree-stroke-goes-limp.html
  9. S

    1993 60 evinrude missing above 3000 rpm once warm

    Sounds like limp mode, no? https://forums.iboats.com/threads/evinrude-50hp-keeps-going-into-safe-mode-at-full-throttle.104416/
  10. S

    Top speed??

    Your confused, I'm not the poster....the not perfect line was about the not knowing if they had a life jacket.
  11. S

    Top speed??

    Not perfect.
  12. S

    Water tube

    Vic, Wasn't being smart and I'm not the original poster. But to clarify, original post said does the Engine have to come off, and I said in general outboard engines have to come off....bla bla bla. As far as above this one particular model the area above the tube is also classified as a tube...
  13. S

    Top speed??

    Perfect. Lifejacket?
  14. S

    Water tube

    < Re-read post 5 and post 9 > "Better not to give you the answers"-----!
  15. S

    Water tube

    Good to know. But, what if there is a hole in the tube above that point? Post 1 "If it has to be replaced,does the power head need to be removed?"
  16. S

    Water tube

    I was referring to the removal of the water tube which I believe the poster asked. Of coarse I could be wrong.
  17. S

    Water tube

    On most outboards, the engines have to come off to allow access. Maybe the carb should be put out to pasture....there's lots around and fairly cheap.
  18. S

    Evinrude 20 Poor Water Flow

    You might find this interesting. Rubber pieces are at the top of the block in the water area slowing or channeling the flow. Let's call it metering.
  19. S

    2007 e-tec 250 lower mount corrosion

    Almost looks like freeze and corrosion issues, but yikes. I had an 09.... and I'm SaltChuckMatt so....
  20. S

    tilt and trim rebuild 2000 50hp Johnson

    I would...wait!-----No, you better not because....yeah, go for ? Pretty sure you thought out loud twice. Have you tried talking to a mechanic at your local dealer? When I was young I would very carefully approach a mechanic and he would eventually tell me....( Bring donuts )
Top