Search results

  1. alldodge

    Fuel System Delivery Issue Mystery HELP

    Great hope @muc can help Looks like a Seapro with VST
  2. alldodge

    Problems starting after fuel filter/water separator change

    https://www.rinda.com/rindashop/
  3. alldodge

    Problems starting after fuel filter/water separator change

    Agree it should be 43 psi and also agree it should start with 30 psi Need a scanner
  4. alldodge

    454 mag mpi chuggles/stalls

    It doesn't run, then it does, they it doesn't Bad connection somewhere, and that as you know will be hard to find
  5. alldodge

    Grease fitting 76 OMC 175

    Measure the diameter of the hole, then find one that meets same
  6. alldodge

    Grease fitting 76 OMC 175

    Generic is fine, OMC never made grease fittings
  7. alldodge

    MC-1 Drive Dog failure?

    I'm not the best guy for how to weld a nut on stainless studs, I've only done steel. Machine shop should know how So far as shimming, it needs to be measured and shimming determined even with using same
  8. alldodge

    What happened to the Strawberries ?

    Wake up, your drooling again
  9. alldodge

    Carburetor issue, I think

    Don't fully understand the term but any kind of back fire or other in most cases is not the carb but timing and or the motor. Intake valve leak Without more info I suggest a compression and leak down test
  10. alldodge

    Fuel System Delivery Issue Mystery HELP

    Not knowing how accurate the gauge used was, 41 is good enough for idle, should be closer 43 at 3/4 to WOT. Again it looks like fuel pressure is not the issue Not putting the guy down, but there are some Marine folks that are great folks and may or may not be Dealer certified. Not that they...
  11. alldodge

    Mercruiser dies after getting on temp

    The rotor Kenny mentions is the one under the distributor cap, it's also where you will find the points and condenser Points and condenser are cheap and a new to you boat should install a new set. Need a set of feeler gauges and watch a you tube vid for any motor to see how to do it, doesn't...
  12. alldodge

    Fuel System Delivery Issue Mystery HELP

    Moved your thread to Merc OB because it's a motor problem, not the toon What was the fuel pressure reading? I'm wondering just what kind of scanner he has, or even if he has one that will actually read the codes. So far mechanic appears to be a parts changer and not a Marine Tech A scanner...
  13. alldodge

    simpli safe

    I'm using honeywell thermostats because they are self contained, no hub needed and works from existing router
  14. alldodge

    simpli safe

    I'm looking my self, and Marina manager likes Nest and has his FL house using them
  15. alldodge

    1991 60-HP wont trim down

    Measure voltages, might be the switch and not relay. Need to do some testing Serial number?
  16. alldodge

    Mercruiser dies after getting on temp

    Very rare to be the coil Did you do maintenance on your points, gap 16*, dwell at 31*-34*? How old is the condenser?
  17. alldodge

    On crank no fuel to throttle body mercruiser 305 EFI

    Sensor assy 892150Q02
  18. alldodge

    Problems starting after fuel filter/water separator change

    Use a voltmeter and see if 12V is at the coil pink/white wire with key ON
  19. alldodge

    Problems starting after fuel filter/water separator change

    Did the kill switch get tripped?
  20. alldodge

    thunderbolt ignition blows fuse after start

    Welcome Leaving key on for days might have over heated the coil. Disconnect the + side wire and see if it still blows
Top