Search results

  1. R

    Engine part ID

    Mice need to pee !----The fumes will corrode the breaker points.----Pull the flywheel and service the simple magneto found under there !
  2. R

    changing timing belt-2009 150HP Yamaha 4 stroke

    Very few car engines run at constant 5000 / 6000 RPM.-----And there is a need to know whether it is clearance engines or not ?
  3. R

    '91 20 hp evinrude possible bad thermostat/heat sensor?

    You need to adjust the stop on that rod.----It is an adjustment that looks wrong to folks when in fact it is correct.
  4. R

    '91 20 hp evinrude possible bad thermostat/heat sensor?

    Slow speed mixture screw.----And the adjustment on that rod.----So 2 things to look at and adjust I think.
  5. R

    Engine part ID

    Remove the flywheel and inspect coils / clean and set breaker points.
  6. R

    Engine part ID

    Rubber boot is a dust cover for choke mechanism..----Not your issue.-----Remove flywheel and check for cracked coils / breaker points that need cleaning.
  7. R

    '91 20 hp evinrude possible bad thermostat/heat sensor?

    Put motor in lowest idle.----Post picture of the adjustable stop on the rod that goes forward to the carburetor.----Many folks are confused on how that is set / adjusted.
  8. R

    '91 20 hp evinrude possible bad thermostat/heat sensor?

    A classic case of lean sneeze.----Adjust carburetor slow speed mix.----Throttle plate is opening too soon is a possibility.-----Put
  9. R

    Hangkai 6hp Outboard Maintenance

    The manual indicates to me / mentions that this is a 4 stroke motor.-----It is up to you to determine what you have.----Do not start this motor until you are absolutely sure what style engine this is !!
  10. R

    Hangkai 6hp Outboard Maintenance

    The spec sheet mentions valve clearance.----Intake and exhaust valve.----As far as I know there are no intake and exhaust valves on a 2 stroke.--Reed valves on a 2 stroke that are maintenance free.------Did you intend to say 2 stroke and 4 stroke instead of 2 cylinder and 4 cylinder ?
  11. R

    Hangkai 6hp Outboard Maintenance

    It talks about valve clearance and yet it calls for oil mixed with the gas.----So what is it a 2 stroke or 4 stroke???----Oil mixed with the gas coats the internal parts with oil on aq 2 stroke..----Oil that is --" burning " ---does not lubricate !!----Any pictures of the power head.----Is there...
  12. R

    Evinrude 35hp Lark Solenoid won't kick

    If throttle is open too far the mercury switch prevents starter from working.
  13. R

    85 hp compression

    What is your motor doing / not doing ?
  14. R

    1987 Johnson/evinrude 110

    These motors were all nearly the same from about 1980 to 1998.----In fact pistons are the same in a 1974 115 HP and a 1998 model.
  15. R

    1987 Johnson/evinrude 110

    Simple adjustment required.
  16. R

    1987 Johnson/evinrude 110

    Are they wire core , yes or no ?
  17. R

    1987 Johnson/evinrude 110

    That would be the outer exhaust housing.------Your power head may be a 90 HP version.----Or an older 115 HP ( powerhead rated ).-----It may involve a bit of machining if you are keen to install that.----Do those plug wires have a metal core?----And why are they so long ?
  18. R

    1987 Johnson/evinrude 110

    What do you mean by ---" belly pan "----here?----Or are you referring to the exhaust bubble ?
  19. R

    What control cables are these?

    Post picture of the other ends.
  20. R

    9.9 hp yamaha 4 stroke crank pressure

    Both pistons move down in the cylinder , so yes pressure can increase in the crankcase.
Top