Search results

  1. alldodge

    Mounting a gen 1 alpha to a gen 2 housing.

    Looks like gimbal rings are different
  2. alldodge

    4.3gi no start new ICM. how to set base timing?

    The Gi should have a MEFI 3 ECM and Delco EST distributor You mentioned ICM, are you referring to the Distributor ICM? While the rotor would point toward number one cylinder, but it should be on the compression stroke and the timing mark on balancer would line up. Where did you get the...
  3. alldodge

    Starter options for 2000 5.0 GL?

    Here ya go https://www.dbelectrical.com/products/starter-for-marine-applications-pmgr-12-volt-cw-11-tooth-50-807904a1.html
  4. alldodge

    Wiring manual

    This is the basic wiring diagram, yours may not have the Acc switches
  5. alldodge

    2000 Volvo Penta 5.7 Gfi with no spark

    Go back to the wiring diagrams previous Check for power at the FP relay, should be 12V on 2 of the pins One of the pins go to the ECM and it should apply a ground to coil side of relay when key is turned to run/on
  6. alldodge

    2000 Doral Port-Side Window?

    Welcome I would contact Taylor Made first then Fex a Fab https://www.taylormadeproducts.com/windshield-glass-solutions/ https://flexafab.com/products/doral-curved-glass-boat-windshield-repair
  7. alldodge

    VP SX-M Carrier Bearing Seal - New Seal Missing Second Spring/Lip

    It could be the seal is no longer made and this is one which comes closest. I did find a couple of the old style available and might be new old stock. At VP site it still shows original https://www.volvopenta.com/shop/0?ft=3852272
  8. alldodge

    1976 888 Fuel Questions

    Would be my guess
  9. alldodge

    1976 888 Fuel Questions

    Running the motor above 1500 can and usually does burn the impeller. A garden hose cannot supply enough flow so impeller runs dry enough to burn
  10. alldodge

    What is a suitable replacement for MARMAC M-1093-D2 on Volvo Penta AQ170 with 270 out drive?

    Suggest contacting Seastar, they should be able to help
  11. alldodge

    New issue cropped up on my transom/bunk position!

    Your saying buy a brand new boat and then modify it?
  12. alldodge

    Verado trim cylinder

    Looking thru the manual 8M0182077 I'll say it was coincidence from hearing the pop and later see a leak. There are only O-rings that keep 2600 psi fluid from leaking. Don't see how this will last long term, and in salt will be shorter Still don't like the leak but at least now I don't see...
  13. alldodge

    Voltage low code 4602-32

    Do agree it got frustrating quick. I installed 1stmate (1st) with a NEMA connection at first while I was also installing the VHF which also used NEMA. Could be where I got into trouble is reading forum comments about 1st not using the NEMA connection even when connected. Others had contacted...
  14. alldodge

    4.3LX & Weber Carb Service

    Compression is way off Seeing 95 to 167 is to much of a span. How your doing the test and accuracy of gauge can have a bearing but my also be engine problems It use to fire up and run rough but not hardly fires and when it does there is backfire. So check spark and timing
  15. alldodge

    Verado trim cylinder

    Don't know what I heard pop but there is no way it should have put a strain on the trim system components. The owners manual list this is where the support lever should be placed for transport. The latch will apply weight on the transom support which holds and supports the entire motor. The...
  16. alldodge

    Verado trim cylinder

    Talking to dealer Tech he said most likely it was the seals. My thought there is the seals are only at the rod ends and neither is leaking on top, it's only on bottom. This should be warranty even if the safety latch caused it to brake something, shouldn't be that flimsy Understand crazy...
  17. alldodge

    Verado trim cylinder

    Your right, I'll do that, but actually don't think anyone here can answer the question. Just tossed it out there just in case Going to take the boat to a dealer maybe next week after rain stops for a while
  18. alldodge

    New issue cropped up on my transom/bunk position!

    Those ratchet straps can put a whole lot of force pulling toward the trailer.
  19. alldodge

    Verado trim cylinder

    Got my manual today, yeah, have another problem :poop: One trim cylinder on SB motor has slight trim cylinder leak and it's on the bottom. While I might be missing an area, I'm passing my hand all over it and only comes up wet on the bottom. This may have been caused by a user but don't see how...
  20. alldodge

    Voltage low code 4602-32

    Bats all changed out, and dang they are heavy Plugged charger in and set to AGM, and go figure it still switched back to LA
Top