Search results

  1. alldodge

    2013 Mercury 20 1F20201HK Leaking gas out the carb mouth (Solved)

    Welcome Readjust float so fuel is shut off a slight bit lower
  2. alldodge

    Divet/crane

    I didn't hear any say "Squirrel" but I am getting hard of hearing and didn't know Mr spell checker was on line
  3. alldodge

    1976 Montego 16- The "Free" Puppy

    No expert but appears to work. Your sensors are 240-33 ohms and spec shows Unit switching: Press the button first, then power on, and then enter the parameter selection mode. You can select the 0-190ohm(European) or 240-33ohm(American) level sensor. switch the units of speed (MPH,km/h or...
  4. alldodge

    1976 Montego 16- The "Free" Puppy

    Didn't see anything on the gauge specifying CAN Buss
  5. alldodge

    1976 Montego 16- The "Free" Puppy

    Should work good, and be way more accurate then original
  6. alldodge

    1976 Montego 16- The "Free" Puppy

    Can replace some stuff but going full modern is mostly out of the realm without some major investments to go to something like NEMA 2000. The helm also doesn't have much space available Could go with miniature gauges or quad type. Maybe install a smaller chart plotter with combo fish finder
  7. alldodge

    Divet/crane

    Might try something like, take a 2x10 and strap cross both sides of the hull. One side of the 2x10 extend out as far as you might need. With boat in the water walk out to the end of the board to see what your boat does. Might try to tip, if not your good with the balance, just need to figure...
  8. alldodge

    Divet/crane

    Welcome Yes it would need to be reinforced. A pedestal seat can hold that much weight but mainly force going downward. A davit will have much more load when the arm is extended. Greatest load will be the opposite of the arm. This is why a claw hammer can easily remove a nail
  9. alldodge

    Houston….. We’ve had a problem…..

    If it is really easy as next to nothing, look close at the splines. The splines should be square and not tapered. Should be able to slide in/out with 2 fingers
  10. alldodge

    LED light device in battery compartment

    Welcome Post a pic Select the Attach files button and upload a pic
  11. alldodge

    1974 Evinrude fisherman pull start not working

    Take it apart and grease it up. The roll pin might be binding or spring is broke or hanging
  12. alldodge

    5.7gs coolant temp sensor

  13. alldodge

    5.7gs coolant temp sensor

    The one your finding is the ECM sensor, the one with one connection is the gauge sender. The gauge sender has no effect on the motor, it's just there as a visual aid for the driver Look for a standard 240-33 ohm sender
  14. alldodge

    Bushnell Rock solid warranty

    Oh I couldn't accept it, but thanks ....
  15. alldodge

    1992 mariner 150hp

    I don't know where you live but search for prop shops "near me" on google
  16. alldodge

    Bushnell Rock solid warranty

    Put a Simmons 3-9x40 scope on my Ruger 22 Mag many years ago. Just guessing it's been at least 15 years Some 5 or so years ago noticed the scope wasn't holding zero. Played with it many times but finally this year looked into replacement. Searched Simmons scope and warranty and it came up...
  17. alldodge

    1992 mariner 150hp

    If you can find a prop shop many will let you try different props if you buy one first.
  18. alldodge

    Prop seals Bravo 3

    You need 3 tools. Need the one with 4 fingers to remove the carrier Need the other 2 to remove prop shafts. They come out together Now to adjust shims there is another tool I spent around $700 on tools to do mine and wish I would have bought to tool to remove the small inner seal. I got...
  19. alldodge

    Prop seals Bravo 3

    Seal part numbers Small inner seal 26-8M0033407 Large outer seal 26-861694 https://forums.iboats.com/threads/looks-like-im-getting-into-bravo-outdrive-repair.617342/
  20. alldodge

    Plastic where zinc goes.

    Welcome Don't cut it off, that is the Mercathode and is more important then the zinc. If the boat stays in the water and is connected to shore power then you need zincs are needed if your in salt water, otherwise need different type depending on kind of water.
Top