Search results

  1. alldodge

    First Aid Kit

    My FA kit has always been a tupperware container that I add stuff to and change things out thru the years. Thought about getting a actual kit but most have some much filler in them that doesn't ever get used Been involved in a couple thru the years that there was things I didn't have so...
  2. alldodge

    1978 Doral 255B. Penta V8

    Yes, muffs go over the outdrive intake holes
  3. alldodge

    1978 Doral 255B. Penta V8

    Welcome point gap .016 to .019 Dwell 26 to 31*
  4. alldodge

    Prop issues

    If you didn't buy it new, then the leg may have replaced with shorter one. Right now I don't know enough
  5. alldodge

    Prop issues

    Welcome, Cavitation would mean the prop needs to be lower. Can you lower the motor any?
  6. alldodge

    1998 kill switch wiring

    Could be, but don't know where the 2 wires go
  7. alldodge

    1998 kill switch wiring

    Kill switch is placed inline with the purple wire from the key. It works like a light switch, it's connected all the time until pulled (switched off) breaking the connection. In this pic the kill switch is part of the throttle, note the connection to purple wire Don't know what the Org/Wht...
  8. alldodge

    Changing my boat gauges.

    If PO didn't solder the wires then that's most likely where the issues are. Looks like he went on the cheap The Dizzy looks automotive and not marine
  9. alldodge

    1985 Mercruiser 224 CID 170 HP Pertronix Ignition

    Tap off on the electric choke
  10. alldodge

    Changing my boat gauges.

    Yes, but a better source would be another place like fuse block. The horn on the ignition feed is not good, already have enough things running on it
  11. alldodge

    please help timing issue is the expected issue help!

    You mentioned one small and one larger connector on distributor so you have EST https://www.amazon.com/Team-Performance-Electronic-Distributor-Applications/dp/B07XTSQDNP Motor should be warmed up. Stop engine and connect jumper. Start motor and bring idle to 1200 RPM for MEFI-1, if you have...
  12. alldodge

    2012 8.1 #6 cylinder missing

    Check compression on 6 and a couple others to compare
  13. alldodge

    Changing my boat gauges.

    Pull the engine 10 pin connector and check pins
  14. alldodge

    Adding a Battery isolator

    Yes
  15. alldodge

    2001 Johnson 70

    Could be
  16. alldodge

    Bilge pump/ blower needed

    IMO might be able to find some parts but no way to find the entire assembly, but just my opinion
  17. alldodge

    Bilge pump/ blower needed

    Looks like it's a Bilge pump "and" Blower assembly but that's the entire assembly https://www.boats.net/catalog/evinrude/rigging-parts-accessories/1973/electrical-1973/bilge-pump-amp-blower-kit-1973
  18. alldodge

    Adding a Battery isolator

    What do you mean in between Bat 1 and 2?
  19. alldodge

    Bravo 3 Shift Cam Position

    No issue with the clunk, motor turning at 600 RPM and clutch engages gears and starts turning a prop
  20. alldodge

    Adding a Battery isolator

    Your saying Isolator and sketch list VSR and pic shows a Relay but calls it a Voltage Sensing Isolator. BTW - Vervor is a China company that sells lots of stuff, basically middle man
Top