Search results

  1. Scott Danforth

    Verify I have found all drain points

    the blue handle is only on mercruisers. the OP has an OMC stringer.
  2. Scott Danforth

    16ft Glasspar w/65hp 2 stroke

    Just materials to do the restoration will exceed $1000.... Probably closer to $1500. Incidentals will be about $300, PPE will be about $200
  3. Scott Danforth

    Coffee maker parts

    I think I joined the ride..... the $2 shaft seal on the bottom of the 5 year old whirlpool dishwasher that rides on the plastic shaft that turns the cheesy disc to pulse water top and bottom decided to leak. because the admiral has a rug in the kitchen, we didnt notice it until the floor was...
  4. Scott Danforth

    Maxwell Smart, "Missed it by that much"

    a cut-off wheel in the angle grinder will be a 4 minute job, including time to debur. 3or4 cut-off blades in the oscilating tool will be a 30 minute job, then change to sand-paper head and spend 10 minutes deburring..
  5. Scott Danforth

    Gas causes mold to form

    you will want to kill the mold before you sand or you just mush the mold spores around. spray nine or oxalic bleach (most toilet bowl cleaners) works
  6. Scott Danforth

    Volvo Penta 5.0gi

    welcome aboard 3862057 is the volvo part for a base engine use the volvo serial number tag (should be just above the starter). the 4990004550 is most likely the GM block serial number. not the volvo penta serial number However there is not much of a variation on the GI motors.
  7. Scott Danforth

    Wiring harness question

    we cant see where the wire goes. we cant troubleshoot your boat. with your information of a black wire tapped up. we cant do much more than speculate. so what did you do to trace the wire and determine what it is for? did you use the chrysler schematic from their manual which would have the...
  8. Scott Danforth

    16ft Glasspar w/65hp 2 stroke

    looks like a stringer and transom job is needed.
  9. Scott Danforth

    installing a remote oil filter set up, got a question....

    makes sense. Crusader (PCM) did a lot of their own engine development including their own induction systems. Merc took the motor from GM and used as-is.
  10. Scott Danforth

    2012 Lowe Fish Ski - windshield missing piece

    look at taylormade's website. https://www.taylormadeproducts.com/hardware/
  11. Scott Danforth

    Looking for a different distributor than my crab cat dist.

    or just get the billet replacement. https://www.amazon.com/Billet-Ignition-Distributor-Cadillac-Pickup/dp/B078HT35C3
  12. Scott Danforth

    Bow sitting high

    300# is a 120qt cooler filled with ice Agreed on weighing the boat to see if you are holding a few hundred pounds of water
  13. Scott Danforth

    Gas causes mold to form

    Don't confuse the thermal mass of the tank for fuel vapors. If there were fuel vapors, the boat would have exploded
  14. Scott Danforth

    Mercruiser 188 Open Cooling System

    Stop. Do not watch the block-buster videos Read this first https://forums.iboats.com/threads/winterizing-inboard-and-i-o.770207/
  15. Scott Danforth

    What Chevy engine is my 2006 350 MAG MPI Horizon?

    There are no marine Gen 2 motors other than a very small percentage of highly custom ski boat motors that were built in the early 90s by indmar. They were short lived. Being MPI, rebuild it stock, or look at going stroker with a 6.2 ECM (then build it to the stock 6.2 specs) Your motor shares...
  16. Scott Danforth

    Keeping the rain and wind off us on the water

    Just duck when she swings the tackle box
  17. Scott Danforth

    What Chevy engine is my 2006 350 MAG MPI Horizon?

    no, its a 1996+ Gen 1 SBC engine with vortec heads. the LT1 (gen 2) was a reversed cooling motor with specific reverse cooling heads for the LT1. The LT1 was a passenger car only. what parts are you looking for?
  18. Scott Danforth

    Keeping the rain and wind off us on the water

    maybe this? https://www.amazon.com/massmall-Diameter-Elastic-Headwear-Umbrella/dp/B00V30PFLK/
  19. Scott Danforth

    Gas causes mold to form

    the mold has nothing to do with gasoline and everything to do with moisture and condensation.
  20. Scott Danforth

    Skeg Q

    dab some paint on it
Top