Search results

  1. Scott06

    Mercruiser 3.0 won't "lock in"

    you should be good to go if it holds pressure and nothing was damaged running that low
  2. Scott06

    Mercruiser 3.0 won't "lock in"

    i think the thread is 3/8 -16" use the fitting off a gear lube pump, although it is hard to find one with a metal fitting vs plastic here is one https://www.amazon.com/Lower-Unit-Gear-Oil-Pump/dp/B0CPXM5VYF here is just the fittings...
  3. Scott06

    Mercruiser 3.0 won't "lock in"

    hard to say from the keyboard. I would do a pressure test first.
  4. Scott06

    Mercruiser 3.0 won't "lock in"

    you can see some staining from moisture especially on top bearing that is above the lube level these were taken out of my gen 2 never had any water show in the drive lube, but had sat for years before I got it (10 years old with only 37 hrs on it). Drive made no noises, got torn down because I...
  5. Scott06

    Mercruiser 5.0 Misfiring

    Sounds more electrical wonder if you are losing 12 v run, either loose battery connections or grounds, or cannon plug between helm harness and engine harness
  6. Scott06

    Mercruiser 3.0 won't "lock in"

    if you still have a greaseable gimbal bearing the grease ends up in bellows when you grease it. If there was little to no lube in drive its going some where. I would start by pressure testing the drive to see where it is leaking. if you are experienced mechanically inclined get the factory...
  7. Scott06

    Mercruiser 3.0 won't "lock in"

    It should be basically full to the vent plug on the side is your bellows full of oil ? Would assume your input shaft is leaking . Given the age of the drive would not be surprised if it needs all the seals .
  8. Scott06

    Mercruiser 3.0 won't "lock in"

    https://www.marineengine.com/parts/mercruiser-sterndrive-parts/30l-gm-181-il4-19871989/0b450801-thru-0c856558/exhaust-system-new-design number 6 in the digram. As mentioned above its below the elbow in the top of the down pipe. Rubber coated metal, rubber breaks down over time and if overheated...
  9. Scott06

    Mercruiser 3.0 won't "lock in"

    Exhaust shutter must have overheated at some point
  10. Scott06

    Lower unit oil leak through weep hole after impeller replacement

    Would think the hot running is what lead to the shutters falling off, usually when water flow is impeded everything on the exhaust cooks off
  11. Scott06

    Lower unit oil leak through weep hole after impeller replacement

    Larger diamter is for the input yoke shaft seal. you will have to remove that to remove the vertical gear to get at this seal
  12. Scott06

    Milky oil from oil cooler failure

    Nice to see it come out ok.
  13. Scott06

    How would a compromised bellows sink the boat?

    Stringer had a huge opening with giant rubber seal I would think that is way more of a risk
  14. Scott06

    Boat had been stored for 19 years

    Drill stringers and transom to verify they aren’t rotted
  15. Scott06

    Mercruiser 3.0 won't "lock in"

    I would inspect the bellows and gimbal while out before digging into it. If they are in good shape and you doo them later- the only thing you loose is pulling the drive which is a ten min job if you've done it before. Bellows and Gimbal are great projects for the off season if they are in good...
  16. Scott06

    1987 Merc 180 (“470” 3.7 litre) won’t idle

    Get a harbor freight ultrasonic cleaner to soak it in. Most failed attempts at rebuilding carbs are because people don’t get it clean enough. Mikes carb parts has good quality kits
  17. Scott06

    Boat had been stored for 19 years

    100% when I bought my current boat in 2015 it was an 11 year old/ 37 hr boat where PO cracked the block. other than the engine, trailer tires/brakes everything else was near perfect. You'd be better off for flip boats to get a blown engine , then go to the junkyard for a long block
  18. Scott06

    Boat had been stored for 19 years

    Some good thoughts on the motor above. take plugs out try to turn it over you may get lucky. I have had engines sit for years and turn over no issue. if it does get hung up pull the drive as the drive, ujoints and gimbal could be locking it up not just the engine. Only huge flag I see is the...
  19. Scott06

    I have a leak.

    Easy to do I tore a CV joint boot installing an axle only to see grease splattered a week later … any sharpe edge Could have been there as the part was delivered to you also
  20. Scott06

    Alpha 1 gen 2 bellows service

    yep I'm in that group. Have a holist but its in 25-27" of water. I leave the boat on a trailer, when I used to leave it in an old barn you parked it outside and the owner moved them in at his convenience. For $12/month storage who cares... My father built a 3 bay garage where it winters now but...
Top