Search results

  1. T

    Intermittent water

    I wish that were the case in my location. It’s not uncommon to find them completely blocked in my neck of the woods and they can be packed so tight you almost have to grind your way through passages to clear them the best you can. To the OP if you want to rule out your pump you could always...
  2. T

    Intermittent water

    Impeller and pump seams ok doesn’t tell us much. When was the last time the pump was serviced and the impeller replaced?
  3. T

    1990 15 hp Evinrude e15eesr won't pee at idle

    I should have asked sooner! Was this just maintenance? Was it pumping okay before you replaced the pump or did you replace it because it wasn’t pumping correctly?
  4. T

    Persistent leak with paper gasket and form a gasket #2

    Permatex ultra black and a new paper gasket. Let it cure for 24 hours before starting.
  5. T

    1990 15 hp Evinrude e15eesr won't pee at idle

    Might be worth taking another look just Incase something dislodged and clogged the line during assembly. I have also found the lines clogged with Vaseline that was used the lube the impeller. Don’t know if you went that route. Only takes a second to fish the pee hose with a small wire just to be...
  6. T

    1990 15 hp Evinrude e15eesr won't pee at idle

    Have you tried cleaning out the pee hose?
  7. T

    1967 40 hp electshift rich/lean trouble shoot?

    Got it Thx
  8. T

    1967 40 hp electshift rich/lean trouble shoot?

    Racerone In the photo of the carb the choke is open. Shouldn’t it not be closed until the motor warms up?
  9. T

    new to me 1970 Johnson 25hp tiller short shaft. locked up

    Me too Picked up a 28 Johnson for $50 that was locked up tight. It had been stored indoors but sat for 10 years. I figured I would take a chance at doing the least amount of work to see what would happen. Worst case scenario I would have $50 worth of spare parts. So I filled the cylinders with a...
  10. T

    Old Outboards ????

    Seems so. A simple Thanks for all who replied would have been nice.
  11. T

    150 Johnson rod bearings snapping

    Oh boy! Rods caps and bearings should have stayed together and been put back on the same journal. Even with new bearings you could have binding on the crank if it’s a high hour motor and if the caps are miss matched to the rods it could compound that even more. Caps and rods are machined...
  12. T

    1985 Johnson 15 hp tiller handle repair

    More info would be helpful here. What is it that you are trying to fix on the tiller handle?
  13. T

    1978 Johnson 115 Electric Choke

    Test your switch. If it checks out look for a blown fuse or damaged wires.
  14. T

    56 Johnson Javelin 30 Restoration / New to this

    For some reason I can’t get the pic of the pump to enlarge but does anyone else see a fuel line going to the pump?
  15. T

    Johnson tn26 Recoil

    Agreed This could be a free or cheap fix. Don’t give up to soon.
  16. T

    Flushing Evinrude 9.9

    I understand your situation now. I don’t think you would get the same amount of result but I don’t think it would hurt anything either. Honestly if the boat is in use daily I wouldn’t worry about that much. A fresh water rinse is good before storage but if using daily the benefit is just not...
  17. T

    Flushing Evinrude 9.9

    Unless the thermostat was open it wouldn’t get you anywhere.
  18. T

    For those who know 70’s Evinrude / Johnson I have a slightly challenging question

    I’m think a bit of your time now to install the correct kit is far better than the problems you could have down the road. Especially if your on the water far from home.
  19. T

    83 - 20hp-30/35 conversion

    Try PN 5007336
  20. T

    83 - 20hp-30/35 conversion

    Should be a package deal in my book
Top