Search results

  1. T

    Loss of power, won't plane

    Personally I wouldn’t use a damaged head.
  2. T

    Method to repair damaged crank/ flywheel key?

    These are good plans. I feel like either may do the trick. It’s worth a try you got nothin to lose right?
  3. T

    Evinrude tell tail not discharging

    Agreed! New to you = water pump service and may as well change the gear oil while your at it.
  4. T

    1989 Evinrude 140hp rough idle

    I think he’s talking about the primmer bulb on the fuel line from the tank. FYI my bulb is after the water separator and I don’t have any problems.
  5. T

    Water Pump not Working?

    Jucebachs Please start your own thread Thx
  6. T

    E90TLESB - Son-In-Law's boat. Runs good but has to squirt Premix!

    What is your starting procedure? I have seen oil come in red, blue, green and purple. They may even be more colorful oil out there.
  7. T

    Draining gas cans

    Get as much as you can out the throw some blue shop towels in the can and blow them around with compressed air if you have it.
  8. T

    88 Johnson SPL - lower unit oil color

    Looks ok Be sure to replace the nylon washers with new ones.
  9. T

    1975 Evinrude 50 won't start Help!!

    Great story Glad everything worked out for you
  10. T

    1986 Johnson 30 water pump

    You can lap it your self. It means to flatten the head. Use a pice of glass or polished stone or a table saw top. It just needs to be a flat surface. Use sand paper to surface the matting surface of the head and remove any high or low areas whichever way you want to look at it. I usually...
  11. T

    2005 175HP VINDICATOR

    Personally I would stay far away from a ficht. Some people have had good luck with them but most have not. Parts are hard to find and you will likely need parts on a regular basis. It was just a crappy technology.
  12. T

    1986 Johnson 30 water pump

    Can it be used for awhile. Thats a million question. You could try to re torque the bolts but in my experience even if stop the leak it will likely start again after a few heat cycles. Your best bet would be to replace the head gasket sooner than later. Don’t forget to lap the head.
  13. T

    1964 Johnson JW-19M Restoration project

    In my eyes if your going to keep it do what ever you want. But if you plan to sell it I would keep it the original color. It can mean a lot to someone looking for a period correct motor.
  14. T

    Johnson trim/lift assist cylinder

    My socket is plastic and just pops off with a flat head. I see you have a Canadian model so I can’t be of much help. I would guess your socket had an c clip in it and should just pop off by prying on it but as rusty as it is it may not survive.
  15. T

    Johnson trim/lift assist cylinder

    So on my 02 model there are two flats on the top to remove the cylinder. They are small flats and there may be a special tool but in a pinch it looks like you could get a pipe wrench on it.
  16. T

    Johnson trim/lift assist cylinder

    I think once you remove the ball and socket you can remove an e ring then drive the pin out. I have one on my 40 hp I’ll take a closer look tomorrow and see if it looks to be serviceable. The parts should still be available.
  17. T

    1986 Johnson 30 water pump

    Is that 100% the correct impeller? The fins look a bit short to me but it could just be the photo. Do you have the old impeller? Is it the same?
  18. T

    New evenrude

    I remember something about the 85 was meant to be a 125 but there was a problem with the manufacturing of the block so the 85 was borne. I recall it being a power house. That was a long time ago. I could be very wrong about this.
  19. T

    OMC 115 Turbojet Bad Piston Replacement Help Needed!

    Yea there are not short cuts here. Do it right or do it again.
  20. T

    Correct prop for mid-60's 18HP Johnson?

    You will need to do a little research with your model number. You may find one here on IBoats.
Top