Search results

  1. Scott06

    Is my Mercruiser fuel injected or carb?

    The mercruiser 2 bbl intake is low rise and tame from a perf standpoint. The stock VP manifold Jimbo mentions is a performance design like the edlebrock and the no name cast iron one i use. i bought my engine as a partial from michigan motorz (“Silver Package”). Came with the cast iron intake...
  2. Scott06

    Is my Mercruiser fuel injected or carb?

    I used this one https://www.michiganmotorz.com/5-7l-4-bbl-vortec-cast-iron-intake-manifold-1996-current any of these carbed intakes with exception of merc one you already own will work well. Certainly other places to buy them as well...
  3. Scott06

    5.7 alpha knock please listen

    Doesn’t sound like the rod knocks ive seen first hand and those made the noise at unloaded idle. either way hard to diagnose from the keyboard
  4. Scott06

    5.7 alpha knock please listen

    Similar noise this guy said head gasket was leaking water into chamber
  5. Scott06

    help help help overheating Mecrusier

    Power steering cooler is a shell and tube heat exchanger bout 8-10" long black tube hoses on either end back on the flywheel cover. Water supply comes up from outdrive to PS cooler, then up to thermostat housing. That's why if you check water flow there you can narrow issue down. if the water...
  6. Scott06

    4.3 mercrusier wires go to??

    https://www.google.com/search?q=mercruiser+4.3+wiring+diagram&rlz=1C1GCEU_enUS915US918&oq=mercruiser+4.3+wiring+di&aqs=chrome.0.0i512j69i57j0i22i30l8.13904j1j15&sourceid=chrome&ie=UTF-8#imgrc=RfLaariOvcib3M In merc wiring orange goes from alternator to starter lug but the wire shown is too...
  7. Scott06

    4.3 mercrusier wires go to??

    Wonder if it is power to a mercathode that may or may not be present ? I’m assuming it was getting power off the 50 a breaker You may find some unused wires in the harness Is that a faded red or orange wire ?
  8. Scott06

    help help help overheating Mecrusier

    Start by seeing if you get the proper water flow up from the drive. First attachment has flow test should get 3-4 qts in 15 seconds up up to thermostat housing. Is the hose that comes from transom housing up to thermostat housing. second photo is your cooling system diagram. Shows water flow...
  9. Scott06

    Soak Bearings in Rust Remover?

    You may want to look at the lower too as moisture got in there some how. If the gears need replacing too may be more cost effective to get a SEI upper
  10. Scott06

    Warning!

    Its been a while since we had a Lou's Q jet centerfold photo ....
  11. Scott06

    Warning!

    This is like the $50-80 bellows kits… a few will work ok the rest will sink the boat… a decent carb kit from a place like mikes carb parts or cliffs , and hour , and a six pack good to go.. and yes you gotta do a few of them twice or thrice until you get it right…
  12. Scott06

    trouble getting reverse.

    had to look that one up ....
  13. Scott06

    Alpha drive for a V8 whats the ratio?

    Any suggestions?? get another mirage or get yours fixed by a prop shop. If you don't have one near you try Prop MD they have a very efficient and reasonably priced mail order repair service. As Jimbo lays out when you get into it there is more to it than diameter and pitch. There is no...
  14. Scott06

    350 Magnum - exhaust riser damaged brass plug

    I think its 35 ft lbs but they need to be flat if they are warped, pitted or otherwise damaged might not seal
  15. Scott06

    1986 AQ131A Carburetor Options

    redline offers a kit to replace the solex carbs with a new webber. Not sure if these fit your application. Would agree with the others finding a decent core or reman one may be difficult. http://redlineweber.com/carb-kits/marine/volvo-penta/
  16. Scott06

    Where ie the engineers spec on my mercuiser 3ltr. Data plate not to be found

    If the tag near the starter is gone look through any literature that came with the boat. Both of my last two boats (bought used) had a folder from the boat manufacturer most of it was safety CYA stuff but in there was a mercruiser booklet that had the serial number for the power package. It...
  17. Scott06

    350 Magnum - exhaust riser damaged brass plug

    What he said....also check the oil doesnt get milky. Could be that there is no water in there but with reusing gaskets and a leak you might have an issue better to make sure there is no water than have an issue later
  18. Scott06

    350 Magnum - exhaust riser damaged brass plug

    Don't need sealant on the new gaskets but you should take out your spark plugs and make sure there is no water in the cylinders. If this gasket leaks water can leak into combustion chambers and get into oil. Can hydro lock the engine and rust the valve stems I would use perfect seal aka...
  19. Scott06

    Maintenance - New owner of 89 Mercruiser 4.3L Alpha One

    Ive run rotella which is good if you have a flat tappet cam. In my newer 5.0 i run mobil 1. 15w50 seems to keep oil pressure up even on good long higher rpm runs or when im towing skiiers for and hour plus straight. The conventional rotella is also about as cheap as it gets
  20. Scott06

    Alpha drive for a V8 whats the ratio?

    A 5.0 mpi is 260 hp Gear ratio will be stamped on the outdrive by the lube vent plug. Willing to bet it is a 1.62:1 In addition to bondos comments if you were happy with the performance and it hits 4800 rpms or so at wot get the same prop. if you are looking to change the performance let us...
Top