Search results

  1. Scott06

    Mercruiser 3.7 (470) wont turn all the way

    If this is accurate while on the lower side this should run ok. For testing you can take the overflow tube off the fuel pump and run it to a bucket until you get the replacement fuel pump, just don't throw your cigarette butts in there... Also verify you aren't getting fuel in the oil, Not sure...
  2. Scott06

    Wakeboard installation

    I don’t have any pictures but i used 1/2” plywood for reinforcement. when i got into it there were really only two options fir where to place the tower on my boat due to mounting space availability. i cut the plywood approx 4 x 10, basically the biggest that would fit. The hull had a curvature...
  3. Scott06

    2004 Volvo Penta 3.0 manifold and riser replacement

    I think typically 5 or so years in salt for manifolds and risers, fresh water they last the life of the boat if winterized. i think your plan of takingoff the elbow/riser is sound. See how bad it looks then you can make an educated decision. you will find witha little basic maintenance 3.0 s are...
  4. Scott06

    1988 mercruiser alpha one water pump issue

    Water pocket cover goes upside down in top of upper and is what the outlet pipe off the pump lands into. It is not included in a water pump kit, but gets melted if it gets overheated good.
  5. Scott06

    1988 mercruiser alpha one water pump issue

    Would also check the water tube is assembled correctly, easy to misalign when reassembling the two halves. If it previously over heated the water pocket cover could be damaged
  6. Scott06

    Divorced choke

    That is a plate that seals the intake manifold exhaust crossover if you want to Remove the choke stove and go with an electric choke
  7. Scott06

    Divorced choke

    https://www.jegs.com/i/ICT-Billet/335/551638/10002/-1# I'm sure there are others at jegs and summit
  8. Scott06

    Which Mercruiser engines...?

    If you have room in front a 5.0 or 5.7 will work fine. If you are not looking for more hp why are you asking about replacing the 4.3 witha 5 something ?? the 4.3 and the sbc have a common lineage front and back are same on blocks , sbc is 4.5” longer otherwise easy swap
  9. Scott06

    merc inline 6 165hp temperature problem ( ive changed the exhaust )

    I think @achris is familiar with the water flow on this engine. I would have concern the copper tube is what constantly supplies water to the exhaust regardless of thermostat being open. usually when thermostat gets removed something is FUBAR …
  10. Scott06

    Removal / Fitting Duoprop

    DN 50 pipe should be really close to 2” ID
  11. Scott06

    Marine Power 454 Engines Fuel Pump

    Are they newer longblocks that dont have a mechanical fuel pump provision? Or cam doesnt have a fuel pump lobe ? agree if you have to replace just use mechanical and get rid if any bs wiring
  12. Scott06

    Marine Power 454 Engines Fuel Pump

    Ok then make sure the pumps are wired through an oil pressure switch if they were added by homer simpson..
  13. Scott06

    Marine Power 454 Engines Fuel Pump

    Those are typical electric pumps set up on carbed engines now. Should be 4-5 psi if working ok. Did u measure fuel pressure off them to carb? Whats the issue you are trying to solve . here is a listing...
  14. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    loose the edge, you went swinging Johnson’s as well, and to be blunt i dont care if your drives fall off your boat. when you find your merc instructions you find they don’t really say much… except test the system at the end. But again could care less if your drives rot off.… if you were...
  15. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    Forgot the link in my previous post https://www.bottomlinemarine.com/prod_cat/images/8m0148835_is.pdf
  16. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    These are what came with my kit. Do you have the transom pucks or the annode under the Gimbal housing. If you have it only under one gimbal housing i would suggest installing it on the other gimbal as well. my friend with a bravo three has two units one on gimbal and one with the transom...
  17. Scott06

    Alpha One Gimbal Ring Hinge Repair?

    Agreed i wouldnt sweat it.
  18. Scott06

    Purpose of spacer on Mercruiser 140, front engine mount,

    The world is t going to end over this but it isolates the bolt from the un numbered horizontal mount casting , otherwise the washers would transmit engine vibration that should be absorbed by the mount #19. Basically you are taking the flexible nature of the mount out of it by tightening it...
  19. Scott06

    TCW-2, use it?

    Yes- my '56 Evinrude 5.5hp says 24: SAE 30 weight , not sure of there was specific 2 stroke back then.
  20. Scott06

    Purchasing 2nd Boat: Jet or Stern Drive?

    One more jet boat detractor- if you like to water ski the wake behind a jet is less smooth in my opinion than a stern drive wake. Also we have a ton of issue with weeds in our jetski so I can imagine a jet boat would be any different. On the ski who cares you are wet anyways but other times when...
Top