Search results

  1. alldodge

    I need a diagram of 1977 presolite trim and tilt

    Don't know if you have a single solenoid or 2 solenoids
  2. alldodge

    Twin Merc. 6.2 Mags with Bravo 3 - EMCT Temperature Overheat Fault - Port side Manifolds (Only)

    Bravoits is checked by removing the intake hose fitting off the inside of the transom assembly, drive stays on
  3. alldodge

    1988 Rogue 2420

    Bad boy bad boy what ya gonna do when formula comes for you 😏
  4. alldodge

    Mercruiser Thunderbolt ignition Question

    5 sec is more then 2 revs, but still not terrible
  5. alldodge

    No go wide open

    Never worked on a wave runner, suggest posting on greenhulk forum. Those guys know them better
  6. alldodge

    Perfectly for 15 minutes then, surging, knocking, and jumping tac

    Runs great except at WOT, its a carb or fuel pressure problem.
  7. alldodge

    20 Member family Vacation

    Looking more of the all inclusive kind of thing so no one has to cook. I know about the vacation home rental I own one. Just trying to figure out a way to get family to want to go somewhere they haven't been, bribe kind of thing. Thought about renting hotel room at a hotel with pool and...
  8. alldodge

    Twin Merc. 6.2 Mags with Bravo 3 - EMCT Temperature Overheat Fault - Port side Manifolds (Only)

    Recon ya got your answer then, if things change let us know
  9. alldodge

    20 Member family Vacation

    Please PM the info, or email if you can
  10. alldodge

    Twin Merc. 6.2 Mags with Bravo 3 - EMCT Temperature Overheat Fault - Port side Manifolds (Only)

    IMO no, 3 tops and 2 years is better. If impeller is used year round, then 4 yrs is ok, otherwise 3 yrs
  11. alldodge

    20 Member family Vacation

    A's and K's are probably 50% each. My thought would like a place that kids could runaround doing kids stuff and adults the other. Keep in mind I have a couple which are under 2 yrs and one (2nd Great G kid) arrives in October :D
  12. alldodge

    Mercruiser Thunderbolt ignition Question

    With it only doing when cold I would let it go and not bother with it. The good thing about the 2 Rev's is it has times to build a bit of oil pressure before starting
  13. alldodge

    20 Member family Vacation

    Have been unable for years to get the kids/G kids and now GG kids together. Starting to run short on time. Would like to find something that can draw them in, spend 20K or so to get them all together at least once. If I can get it done once should be easier maybe the next time Never wanted...
  14. alldodge

    Mercruiser Thunderbolt ignition Question

    Not sure about a 2010 TBV but the old ones didn't have a delay. When I start my MPI and its cold, the ECM has it crank over about 2 full revolutions befoe it will start. When warm it doesn't even turn over 1/2 a Rev before firing up Could be, its built into the system. I don't know, just an idea
  15. alldodge

    20 Member family Vacation

    Looking for ideas for extended family vacation. Tought about getting a local hotel with pool and having things catered, but need something less stressful and more all inclusive. Thinking of before this Christmas and maybe a cruise or USA site. Could try the Bahamas or the like, but then...
  16. alldodge

    4.3 TKS "Run On" fixed but Slight Loss in Performance

    Might be from run on (dieseling). Its now fixed so run it some more and see if it clears up
  17. alldodge

    Mercruiser Thunderbolt ignition Question

    Look at the module inside the distributor and see if it has 2 wires or 3. If it has 2 wires, it might be worth getting the replacement 3 wire version. The 2 wire type has a grounding issue
  18. alldodge

    Circa 2008 4.3 GXi (SX-A) Possible to increase power/performance?

    Has another thread with same subject (against rules) https://forums.iboats.com/threads/have-14x19-4-blade-on-4-3-gxi-upgrade-to-stainless-steel-worthwhile.759171/
  19. alldodge

    Have 14x19 4 blade on 4.3 GXi. Upgrade to Stainless Steel worthwhile?

    Pulling skiers you need to get the RPM up fast. A 4 blade prop bits more so there is less slip, getting more slip out of the hole will help. Try a 3 blade 21 (same as 4 blade 19) because it will slip more on the hole. If you want to flat pull someone up, try a 3 blade 19 and go easy pulling...
  20. alldodge

    The job of Marine Technician

    Thanks for the tip
Top