Search results

  1. R

    1972 mercury 402 40hp two questions

    Replace the little oil recirculation line.----Goes from near bottom of engine to near upper bearing.
  2. R

    Johnson 50 hp air/fuel issue

    Bad reed valves.-----Blown bottom crankshaft seal.----Bad piston / rings.----Some will argue , but remove cylinder head and inspect stuff.
  3. R

    The water drain holes I don't understand

    Bow thrusters.
  4. R

    1988 force stator 125hp

    What ohm reading do you have on yours ?
  5. R

    1990 ish Evinrude 25 HP - Screeching from the controls

    A 1990 is shown to have a temperature switch.----It is likely the overheat warning and needs to be investigated !----Sad that folks do not replace impeller every 5 years or so.
  6. R

    1995 four winns fling

    Do a compression test on this motor.----Post the numbers.
  7. R

    The water drain holes I don't understand

    Agreed-----Bow thrusters.
  8. R

    1962 evinrude needle valve assembly on carb

    Use a 7/16" wrench and tighten the packing nut on the low speed needle !!----Add more packing if needed.
  9. R

    Looking for guidance please

    Check valve clearance.------Check compression ( throttle open ) ----The powerpack ( big $$$ ) has an optical sensor.-----Does spark jump a gap of 3/8" on both leads ?-----Perhaps oil pressure switch is acting up ?
  10. R

    1999 90hp FICHT~Premix Conversion?

    The fuel does NOT go through the crankcase on these FICHT motors !!-----Crankshaft and bearings would not see any oil.------Motor would quickly come to a " dynamic halt " and be ruined.----
  11. R

    1972 mercury 402 40hp two questions

    The oil recirculation line is clearly visible in the second picture.----About 3/16" diameter and it appears to be cracked !
  12. R

    1972 mercury 402 40hp two questions

    Prevents operation of recoil when motor is in gear ?----You should replace the oil recirculation hose.
  13. R

    Evinrude Fastwin 18 No Full Tilt Lock

    Perhaps you need to tighten the steering friction.
  14. R

    Centering boat on trailer (solo) without trailer guides? or DIY guide advice

    Roller at the back of the trailer half submerged.-----Pull boat on and it will center itself.-----When winch takes too much effort , back the trailer in about 4 or 5 ' more and repeat.-----Put my 30' boat on the trailer that way.-----Never an issue.
  15. R

    1983 60 hp Evinrude shift rod height???

    It be 20-29/32"
  16. R

    1966? Evinrude Big Twin 40 help

    Lots of short shaft parts can be found.-----Try E-Bay----evinrudeparts.ca-----Should be easy to find.
  17. R

    ‘84 Evinrude 15 water pump issue

    Andrews----try----evinrudeparts.ca----About $6.39 + likely $10 or less shipping !!!
  18. R

    ‘84 Evinrude 15 water pump issue

    Thermostat cover gasket is listed online for $4.01
  19. R

    Evinrude Fastwin 18 No Full Tilt Lock

    Make up a " u-shaped " bracket.----Same size as tilt adjusting pin.-----About 6" total.----Than clip that into outer holes and on the reverse lock clamp.----Should keep it raised for trailering.-----Got a box full of those brackets ( 40 HP ) from a dealer , he used to give them away with each 40...
  20. R

    Can't decipher serial number on Johnson Super Seahorse

    1965 model
Top