Search results

  1. alldodge

    Help a new guy out . Pcv valve

    Can also get a piece of flat stock and make one which bolts down on top the flame arrestor. This ones on my motor and is cheap https://www.cpperformance.com/p-68144-retainer-mercruiser-805314.aspx
  2. alldodge

    Adding 100+hp. Would you re-prop ?

    My 10K lb cruiser is running B3 2.0 ratio with 26's with 530hp 509 turning 5200 rpm
  3. alldodge

    2003 Ebbtide Mercruiser 3.0 engine rattle? Normal?

    Do you see 12V on pin b of the coil pic post 11 ?
  4. alldodge

    Adding 100+hp. Would you re-prop ?

    Agree with others to test first, but also agree "IF" your Tach is accurate your going to need more pitch or lower ratio. Being at 26 pitch, I'm thinking the ratio was changed from original since you were getting 4800-5000 at 48 mph. When back together get a hand held Tach to verify. Most are...
  5. alldodge

    1987 Bayliner Capri 3.0 - ignition switch does not turn on starter

    Look for an inline fuse going to the B terminal behind the helm
  6. alldodge

    Gasket

    Manual 1 doesn't show it during build up. Parts breakdown does show in between block and plate. Seeing that the adhesive showing being affixed to plate, I would reinstall it that way. Seal goes on with raised portion facing AFT on the bottom. Then plate, then flywheel...
  7. alldodge

    Gasket

    What motor and what part is the plate (flywheel cover maybe?)
  8. alldodge

    Registration with no serial numbers

    KY doesn't require boat trailer plates, my comment stated car trailer.
  9. alldodge

    Registration with no serial numbers

    The good thing with home made (at least in KY) is what its taxed at lessor value. Says mine is worth 100 for 2 axle 18ft car trailer
  10. alldodge

    Registration with no serial numbers

    No issue hand made for me, no sherif, constable, nothing. Sent paper work in, signed off and they sent me the plate to install on my car trailer
  11. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    I use this site for VP parts, and mine is US yours should go to GB I think https://www.volvopentashop.com/epc/en-US
  12. alldodge

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    Easiest way to find GM part numbers is go to a website like "GM Parts Direct", or go to place like Summit Racing and find it that way
  13. alldodge

    Wiring diagram for 5.7 GSi PEFS? Or AQ271C? Ideally both?

    Like with all threads,need to post updates or new questions otherwise we think things are ok
  14. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    I use trim down every time the boat goes in the water. Its up some while on the trailer because if it was full down it would drag on the ramp. Put in REV and when it floats off and gets a bit away from the trailer, it goes the rest of the way down So I have to retract what I said at first
  15. alldodge

    Drive lube dropping?

    If the drive has not been run much since it was replaced, I wouldn't think to much about it. If it was run a few hours and topped off, and dropped again I would look into it
  16. alldodge

    Boat won't move

    I'm thinking the splines on the coupler stripped out not moving at all
  17. alldodge

    Boat won't move

    Its running but won't move, means its either the coupler, prop hub or drive. As ding mentioned, put in gear and spin the prop. If it spins its in the drive If it doesn't, start motor and put in gear. See if the drive shaft is spinning behind the motor
  18. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    Did notice it posted as 25 but I meant 20 It says 15 so I would keep it at that Look in your shift handle to see if there is any chaffing or the wires going on
  19. alldodge

    Mercury Trim Switch Blowing Fuse (unusual circumstance)

    Ok got it, that shouldn't happen If you have a manual should the fuse be 15 amp? Otherwise I don't know
  20. alldodge

    Honda BF15D will not stay running (Purchased Used)

    Impeller missing fins and temp sender broken. My first thought is the motor over heated and there is a motor issue. Don't see a temp sendor keeping any motor from running. Folks lie all the time. Honest folks get taken all the time Do a compression test
Top