Search results

  1. alldodge

    Lost our best fishing buddy

    I sort of have always taken the easier way out by always having two. Unable to remember when I didn't have a buddy other then in the 70's when in the USCG. The easy way is to always have two, one old and one young. When the old one goes, the younger one helps get ya past it. Then get a pup...
  2. alldodge

    Mercruiser 3.0 Fuel Issues

    No need for new thread unless you want to get maybe more input, and nothing wrong with more input If this happens when the motor is cold but not when warmed up, then its the choke, and it needs adjusted If it happens all the time at low idle, then its mixer screws and/or float settings
  3. alldodge

    Lost our best fishing buddy

    Until you get another buddy, this will continue. Everywhere I look I see Tigger, next to the bed, the chair, in my lap, out in the shop, just everywhere. I'm trying for the first time to see if I can get by without a buddy, and so far its not working very well
  4. alldodge

    Lost our best fishing buddy

    So sorry for your loss, pups a the best friends. Agree, sure lucky not having to put him down Had to put my almost 17 year old buddy down last month. That vet trip was really ruff.
  5. alldodge

    496 Mag HO Slight Idle Surge

    If its just slightly above idle 7 to 800 rpm, might just be the nature of the beast. Another member here and one on OSO seems it an issue with programing by Merc Has it been doing since new or just start?
  6. alldodge

    master bath remodel

    Your no fun at all. Using red/blue keeps all the guess work out of it :D
  7. alldodge

    Temp Gauge Not Working

    Its either the wrong gauge or its miss wired. Check voltages and grounds Check the gauge part number North America standard is 240 ohms (cold) to 33 ohms (hot) European standard is 33 cold to 240 hot
  8. alldodge

    DP 1.95 SM outdrive hosed

    Unknown, some times its just stuff happens. If you trust the Mechanic then that's all it is. Normally vibration when turning is gimbal or U joints. Bearings in the drive will give vibration and or noise when running. The drive can be rebuilt, it could be the marina doesn't have the...
  9. alldodge

    Temp Gauge Not Working

    What do you mean it goes down? Mean it pegs hot maybe?
  10. alldodge

    Prop Question

    I'm getting 15 now so its good. Some how going from Knt to mph conversion I guess was the issue
  11. alldodge

    Boiler Catastrophy ,Have to replace it ,Which to get?

    I never rent a tank, always buy
  12. alldodge

    Boiler Catastrophy ,Have to replace it ,Which to get?

    Agree but your just talking prices/BTU, high E propane can be cheaper to run Just search for comparisons
  13. alldodge

    Boiler Catastrophy ,Have to replace it ,Which to get?

    Unable to answer that question, but why would you go back with oil? Propane is more efficient from what I'm reading
  14. alldodge

    Prop Question

    With a 2.15 it just means there is more slip Think of it this way. If the motor is in neutral and the motor is reved up, it takes next to no fuel to do that. Put a lower pitch prop on and the rpms go up but there is less load so no more fuel used, and maybe a bit less from no working so...
  15. alldodge

    Prop Question

    Rule of thumb is 19P 4blade = 21P 3blade Don't know the gear ratio but the prop slip is bad. Using 2.5:1 ratio it showing 45% slip Might want to try a 14.8 diameter 17P 3blade
  16. alldodge

    Aqua Power 95001 Heavy Duty Docking Light upgrades?

    Light is good but don't need aircraft landing lights. Car headlights are 2k to 4k lumens, and a boat doesn't "need" that much
  17. alldodge

    Old ford 302 no spark

    For the most part it doesn't matter Remove all plugs, piston should be below TDC. Install stop tool and rotate crank until it comes in contact. Mark damper location Rotate crank in reverse rotation until until it contacts again. Mark damper location. Center position between the 2 marks is TDC
  18. alldodge

    Mercruiser 3.0 Fuel Issues

    List a Carter fuel pump and should output 5.25 to 6.25 psi With it's output at 9, then something is wrong with the pump. It also doesn't use 2 gaskets
Top