Search results

  1. R

    Low compression #5, 115hp inline 6

    These inline 6 cylinder motors run really nice in in good condition.
  2. R

    Not repair related...yet...Johnson 70ELCNB

    Post results of a compression test .----Should be around 14o PSI on a motor in good condition.----That motor in good condition will last many years.----It is simple to operate and maintain.----As a novice boater you need to accept that there are many things to learn about the operation of a 2...
  3. R

    johnson 90hp vr4 fuel pump question

    Not going to argue here.-----------I would install the 2 nipple pump.-----Neat and simple to do.
  4. R

    110 Johnson maintenance

    Yes , motors with lower compression will run.----Will not run the best.-----Looked at a 30 HP motor last year and showed owner the scored piston.----He said ----" it still runs ok " ----Called me a while ago and said no issues so far.----I think it is because folks with older / iffy motors have...
  5. R

    johnson 90hp vr4 fuel pump question

    It does NOT have a pulse hole at the back !---I do not believe that hole is drilled through on that pump.-------And on that motor I would use a 2 nipple pump and mount it directly over the pulse port on the intake manifold,----Find that just in front of the starter.
  6. R

    Possibly ran without oil. What to check?

    Fixed the VRO pump or the conventional $100 pump on the side of the top cylinder ?
  7. R

    Johnson 140 bogging down

    Change fuel filters.----I think there are 3 of them.----Water pump impeller changed on your JOHNZUKI ?
  8. R

    DT200 Power Head Experience - Remove Cylinders?

    Worked on a V-4 and I do believe everything needs to come apart to get the cylinders away from the main block.----Many hrs of work.
  9. R

    evinrude looper lower unit help

    should fit
  10. R

    18hp evinrude lower end

    ???-----No , you would be shocked at what ----" every piece " ----Would cost.-----Take apart / inspect then decide.----Used lower units are plentiful in some areas.
  11. R

    evinrude looper lower unit help

    Which driveshaft ?----Yours or your friends lower unit ?----Or post some pictures of your friend's unit.----From the side.
  12. R

    Did my lower unit get damaged?

    Pressure test the gearcase.
  13. R

    1962 Evinrude Starflite IV 75hp no spark HELP!

    Is the timing correct between crankshaft and distributor ?
  14. R

    evinrude carbs

    There is an issue with the float / float valve.----Take carburetor apart and inspect.
  15. R

    18hp evinrude lower end

    Easy job.----No special tools required.----Pay attention to the pin to locate the forward bushing for proper lubrication.
  16. R

    evinrude looper lower unit help

    Maybe your friend thinks his is a crossflow.----In 1995 there was a 60 degree looper and a big 90 degree looper.------Post model # to sort this out.----See if there is a part # on the driveshafts !----A 1995 crossflow will fit the big 90 degree looper from 1989.
  17. R

    evinrude looper lower unit help

    Yes they do interchange !!!----Shift rod needs to be swapped out.----And the correct shift rod height has to be set.
  18. R

    9.8 hp throttle hook up/ lightning stator disconnect

    There is another piece missing.-----It rotates to change timing.
  19. R

    9.8 hp throttle hook up/ lightning stator disconnect

    You are missing some pieces that must go under the flywheel.
  20. R

    110 Johnson maintenance

    Cold readings are just as meaningful as those from a warmed up motor.
Top