Search results

  1. alldodge

    5.7 TBI advanced timing

    Thanks for the number With the EST ignition are you jumping the DLC connector which puts the motor is base timing mode?
  2. alldodge

    5.7 GSI running issue

    This is a GSI and the oil pressure has no direct connection to the fuel pump. This isn't The GSI but so far as the oil switch its the same The green/yellow does not go to the key switch, and the ECM applies a ground to this wire, no power
  3. alldodge

    5.7 GSI running issue

    I think there is a fuse and relay on the motor, but being a 87 not real positive Also appears my last post didn't show up with the wiring diagram, so will try again
  4. alldodge

    transom leak

    The top of the pin goes into a upper bushing. You've gone this far I would replace then bushings if there is any play what so ever.
  5. alldodge

    transom leak

    Seal does go on the bottom then
  6. alldodge

    5.7 GSI running issue

    Sounds like there is a difference between 87 and newer motor, but it was working before, so if you connect wires from pin 1 thru pin 10 you have it.
  7. alldodge

    92 mercury 40hp power trim seal kit

    It amazing what you can find with a serial number. The kit shows up as 813432A3 and appears to be around $30
  8. alldodge

    Hit Rocks with my Mercruiser 3.0

    Might be might not, just not enough info for me to make a guess. Is the battery fully charged and can read 12.8V? .There is a slave solenoid on top the motor. Jumper across the two top terminals to see if the starter turns the motor over. Looks like this
  9. alldodge

    transom leak

    The washers are here
  10. alldodge

    transom leak

    The seal goes in after the two upper bushings are installed. The lip goes upward (item 5)
  11. alldodge

    Another fuel pump issue.

    You have an EFI motor and the oil pressure switch does not make a connection for power to the fuel pump. The switch sends a ground to the ECM telling it that there is a loss in oil pressure. The ECM supplies the ground to the fuel pump to turn it ON/OFF Don't know if you have a MEFI 1 or 3...
  12. alldodge

    4.3l Volvo Penta wiring need help

    Would help to know which 4.3 it is? Here is a GL 5.7 but wiring would be the same for a V6
  13. alldodge

    Sitting for 5+ years and fires right up

    A 2002 Crownline 6.2 MPI with 152 hours. Boat has been at the same slip for at least 10 years. Been sitting most the time and several years ago it was looking pretty bad, covered with years of tree pollen and crud. Saw the owner on it cleaning it up, and then he left. For the next 5 or more...
  14. alldodge

    What type of fitting

    Below is a fitting on a 9000 psi pressure gauge and I need to know what kind/type it is. Trying to find an adapter to go from the gauge to an npt fitting
  15. alldodge

    Charging issues

    Your link is for installing an isolator, this is a different issue. The 12V is read by the helm voltmeter on the purple wire. Your meter may be off, but get a hand held meter and measure on the Orange wire on the ALT or the starter post.
  16. alldodge

    Laptop with Win 7 Pro

    Wife's desktop HD crashed and now I'm looking for a laptop with docking station to replace it. I want to stick with Win 7 so all of her old software can be installed. Stated looking at Dell XPS 9360 and Levono and others, but then thought about the Win 10 issue. Computers keep changing and...
  17. alldodge

    Dry joint Riser on Non- dry joint Manifold?

    I have a box full of 4 inch boots of various types, also have some other exhaust tubes when I was trying to re-plumb my thru hull exhaust. In short there is hardly any bending of the exhaust boots. I think your going to need 14 degree elbows. Just for further clarifications so we are...
  18. alldodge

    1983 Mercruiser 5.7 Exhaust Riser Gasket

    Yes I got it now, yours are straight across. While you could use the gasket in the amazon link, you should use the one you have. The gasket 27-863726 are used with risers extensions. This allows more water to transfer into the riser, then the gasket your using is installed to connect the...
  19. alldodge

    94 Mercruiser 3.0

    Here is how you replace and set points
  20. alldodge

    8.1GI-a audible alarm issue

    From my VP manual I'm seeing 3 items for a solid alarm Low oil pressure Exhaust Temp High Engine coolant temp high (Port and starboard) All the alarm switches have one terminal on them except the coolant temp, it has two Note this is a MEFI 4 If you have a 555 ECM there could be more
Top