Search results

  1. alldodge

    Repair Cylinder or replace block

    Don't think so. The oil ring is made of two rings and a spacer. While the compression rings can be installed upside down the oil ring cannot.
  2. alldodge

    2005 Mercruier carb w/210hp???

    The 210 is not quit so much slight of hand. The manual shows carb at 205 and the EFI at 210. So your talking about 5 HP. Now the 190HP rating is from the Bodensee and Swiss Regulations and comes from testing done at different RPM's
  3. alldodge

    Corsa Exhaust Diverters

    The short answer is No. The 4 wire uses a high and low current legs, one is high to bring the solenoid in, then switches to lower current to keep it in.
  4. alldodge

    Inboard '95 Mercruiser GM 350 EFI Magnum Skier limited top speed

    Did a quick read back thru every post, not in depth read. I still want to know is what is the fuel pressure at the TB while running from idle thru WOT? The TB has an inlet fitting and a plug fitting. In many cases a fuel pressure sensor is installed in this area, such as pic below Note there...
  5. alldodge

    Switch and fuse block wiring

    The only supply wire that might be in the panel is to light it up, otherwise there should be no main power wire. The switch panel shouls it bing used by a different Blue Sea fuse panel without Pos or Neg buss bars. This one shows power being daisy chained, then other shows individual leads
  6. alldodge

    Switch and fuse block wiring

    Fuse panel is where main power comes in and goes thru fuses. Other side of fuse exits to individual switches. Other side of switch goes to individual units being powered. Return legs comes back to negative fuse panel
  7. alldodge

    tilt / trim fuse and switch

    They are pretty standard these days, but look at the ones you have and see if they match these https://www.amazon.com/Chrysler-Force-Relay-PH360-0002-882751A1/dp/B01BTV2CZE This is how they are arranged, you will not use 87a pin and many don't have it there. pins 85 to 86 energizes the relay...
  8. alldodge

    Velvet Drive 71C rebuild trouble

    Oil flow
  9. alldodge

    1977 mercruiser 233 lower shift cable

    If you get the new style cable, it needs to be installed from the front. The threads are chased (cleaned) to allow cable to go in. OEM parts are better then aftermarket in this case. If you happen to find the old style (not made any more), then it can be installed as original. There are many...
  10. alldodge

    1984 Mercruiser 140 repeatedly needs timing readjusted

    I would look at the pin which holds the gear on the distributor. If that's good the look for any play in the shaft an up/down
  11. alldodge

    Fuel pump not pumping - looks bad

    Don't know what pump you installed other then its a Carter, but it doesn't look like the ones for a 4 cylinder from 1982-1994
  12. alldodge

    Non-Vortec 5.7 Mercruiser Themostat Housing Question

    Not knowing which model, I'm going to assume you have one similar to the one on the left Thinking you want to go to new style like this, which is a V6 but is the same for you. As FT mentioned, if you have a bravo drive then the inlet hose comes from the belt driven pump. You will also not...
  13. alldodge

    350 mag mpi surging under load

    Last set
  14. alldodge

    350 mag mpi surging under load

    The actual screen shots were pretty small in jpg so chopped it up
  15. alldodge

    Livewell Headache

    Your system should be setup the same according to the site. As Harley said, the Auto just turns the pump on and back off every so many minutes. The valve going to the pump should work the same way, and you should have the same similar setup. It could be "maybe the pump is gone" :noidea: just...
  16. alldodge

    Livewell Headache

    Have not used one but looking at the design I would say the valve on the pump should close off or open tubes as needed. http://www.g3boats.com/uploads/sites/4/website/Pages/676/g3_2012_owners_manual-optimized.pdf
  17. alldodge

    1988 mercruiser mei 7.4 thunderbolt - no spark

    Howdy This is the troubleshooting guide to the TB ignition. It is for a TB-5 but TB-4 is the same. Test lights are good for quick checks but you need a voltmeter
  18. alldodge

    Mercruiser 3.0 TKS possible failure

    Your symptoms tell me its the accelerator pump, not the module. The module when cold and open allows the carb to put more fuel in the motor. Once warm the module closes off and then there is less gas. If the module is open (retracted) then you should hear some extra hissing from the carb...
  19. alldodge

    Inboard '95 Mercruiser GM 350 EFI Magnum Skier limited top speed

    If your testing the pump only connect direct from the output of the high pressure pump. The regulator or injectors are not in the mix and have no effect. If pressure drops back off then the HP pump is leaking internally. If block off is measured after the TBI then the regulator and the...
  20. alldodge

    2001 MC 5.0 EFI Throttle Body-appear to be running rich. Trying to help a friend

    Make a scan tool with a paper clip and a resistor LED
Top