Search results

  1. flashback

    Lehr 5 hp piston rings

    Quick search on ebay I saw some..
  2. flashback

    Water in the drive shaft bellow

    If you're smart you want to replace all the rubber bits. And the u joints as well. Rust on the outside probably means the bearings are pitted.
  3. flashback

    Engine wont shut off with key

    You got a lot of help, I understand frustration, but some how your ignition is being fed when the key is off. How are you shutting it down when running?
  4. flashback

    '95 OMC 5.0L fuel line

    Shade tree for sure, looks like something I'd do, if the hose is good then just snug the clamps occasionally.
  5. flashback

    Hi all from new Searay owner

    If you had the old 5.7 you probably would get busted after a few pints! Heck they hit 4 knots at idle.. I think you found a boat set up perfect for your needs..
  6. flashback

    Anyone know where to find this piece?

    That's right up my alley! JB would do it. Ain't no stress on the part unless you run into something..
  7. flashback

    Hi all from new Searay owner

    It should work great for camping on the lake plus you get a bunch more storage room.
  8. flashback

    Anyone know where to find this piece?

    I would call it a bow end cap for the rub rail. Probably like finding a needle in a haystack given the variety of bow profiles.
  9. flashback

    Hi all from new Searay owner

    If it's anything similar to my 95 220 overnighter then it probably won't plane. Mine is a heavy boat...
  10. flashback

    Alpha one Gen 1 U joint removal

    Are ya feeling lucky? With the corrosion on the other bearings. I don't know much but I would break it down just to see..if it looks good then put it back in ..
  11. flashback

    Question on tune-up of points ignition & wire/spark plug order

    That brought back a few memories under the shade tree!
  12. flashback

    port side exhaust elbow over heating.

    Thanks, that's what I hope to do as there are so many versions I wouldn't know which to get. I just need to get from point A to B. It won't be as pretty but then neither am I. LOL
  13. flashback

    port side exhaust elbow over heating.

    Had some decent weather and got the bits back on the engine today and cranked her up, ran it up to temp, manifold, elbow and down ell were just warm to touch not hot. but like Lou C mentioned the starboard down ell got a bit hotter so that's something to watch for sure.. I also found a small...
  14. flashback

    Pull starter pinion replacement

    I think it's a roll pin so yes a bit of force.
  15. flashback

    PLEASE HELP... I'm at a loss of what to do!

    Sounds to me that you're X Just thru you a curve.. you want to find all the drain fittings and be sure they are there and come winter in KY you will need to remove them so your engine doesn't freeze up..
  16. flashback

    350 mag water pump impeller change question

    I'm dealing with a similar situation And I only brought it up because I have an exhaust hose that's crispy, . I have nothing to offer you but I lurk All the threads, it's knowledge I'm after.. I think my elbow is rusted to where the water won't flush. I will not highjack your thread but will...
  17. flashback

    350 mag water pump impeller change question

    Would 10 minutes running burn up any soft parts in the exhaust system? I guess it is fed by the same pump?
  18. flashback

    Install new exhaust coupling on riser

    I was recommended quicksilver power tune.
  19. flashback

    Steering actuator vibration

    Wow, if that was a.mercrusier I'd be very careful but don't know anything about a VP.
  20. flashback

    Recommend a dwell meter

    I have one of those and it worked well on my old scorpion.
Top