Search results

  1. flashback

    Mysterious part in bilge - what is it??

    Yea back in the day they called it a rotor button.
  2. flashback

    Can only suck out 3 liters of oil from 4.3tks

    Seems your leaving about a quart behind, not a big deal, your gettin 75% of it. Tilt the bow up or down and you might get a bit more..
  3. flashback

    port side exhaust elbow over heating.

    I have an extra elbow gasket just for that situation. And I got a infrared thermometer as well, now I just need to figure out how it works..I will keep close watch on the temp differential when I get it running. The engine runs good and the last thing I want to do is fry it..
  4. flashback

    port side exhaust elbow over heating.

    The shutters are totally different from what I took out. They're rubber but I believe they'll fit ok. Merc's mini instructions said they will..rest assured I'll let you know one way or the other! Thanks to all of you and have a great holiday!
  5. flashback

    port side exhaust elbow over heating.

    Well I have some of that leftover from the lower shift cable installation last fall..so I'm good. If this repair is successful I'll do the other side this fall. If not then I'll be back.... LOL
  6. flashback

    port side exhaust elbow over heating.

    Thanks! I can do the file procedure, was going to wrap a sheet of 220 around a piece of hardwood flooring but I think the file is better..the new elbow has paint on the flange surface which I probably should sand off as well. I can probably find the hose fitting at a plumbing shop.
  7. flashback

    port side exhaust elbow over heating.

    I didn't have any luck clearing the crud out of the old elbow so I went to a merc shop and got a new elbow, shutters, exhaust hoses and gasket. I still need to find a brass fitting for the elbow hose as the old one would not come out of the elbow after 27 years... And as usual nobody has any...
  8. flashback

    One manifold hot (5.0)

    I'm dealing with much the same problem, I did cook the lower hose, the manifold is questionable but the elbow definitely scrap iron. I'm going to replace it with new hose and if it works I'll be lucky and when fall comes I will change all of the exhaust system. The other side can't be far behind..
  9. flashback

    Should I buy-2002 Sea Ray 240 Sundancer

    Your not gonna like how it handles with 3 or 4 inches of slop..Heed the above post from Scott, and will add that the tinny and an outboard motor may be the best choice for a last time buyer as well..
  10. flashback

    Converting 260MIE RH to LH.

    If you reverse polarity on the brushes or the field I would think it would work. The bendix would be another matter. I'm in way over my head but If these thoughts help you I'm good. Besides I'm curious and now I will get notifications..
  11. flashback

    Shifter is turning the upper shift shaft when put in forward or reverse.

    It's the arm on the upper end of the shift shaft. It has a roller on it that engages with the cable connector. It can dis engage on it's own quite easily while installing the drive.
  12. flashback

    Shifter is turning the upper shift shaft when put in forward or reverse.

    The cable connector slips off real easy, I been there.
  13. flashback

    Anyone Seen these?

    Don't spend the night at the local holiday inn!
  14. flashback

    2 stroke to 4 stroke

    Give it to a friend who has a 2stroke, if you can afford a new engine you sure don't need to worry about a few gallons of gas...
  15. flashback

    Lower unit wont separate from top.

    If you're the first owner then that's probably accurate, ot
  16. flashback

    Lower unit wont separate from top.

    I thought all the gearing options were in the upper half and the lower was the same..
  17. flashback

    Outdrive Popping

    I guess that with a stout enough hoist you could yank the motor out with the drive still on but I would have bet my SS check against putting the motor back in. I'm learning every day..
  18. flashback

    Anyone Seen these?

    I don't care what y'all say, that thing will look good going down the road on the trailer ..
  19. flashback

    port side exhaust elbow over heating.

    Are you saying that the riser might have a few days left in it. I will poke around in it. Maybe a bit of muriatic might be a help.. I didn't see any indication of rust in the throat...
  20. flashback

    port side exhaust elbow over heating.

    Well I guess I'm gonna get some new risers and hope for the best with the existing manifolds. I can't find a part number on the risers or the rubber bellows that was burnt. the upper bellows has a number on it and is still quite pliable. are they both the same? The metal gasket for the...
Top