Search results

  1. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    This is what I need right? https://www.marineengine.com/newparts/part_details.php?pnum=MERF2A654983 Got it out Cheapest I found is 471 on Ebay. So Jerry where did you get the $25 one? Wonder if they sell the nipple fitting only?
  2. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    That sticky deals with the valves I don't see any references to the broken Banjo bolt. I could be wrong
  3. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    I moved the top one. The bottom is stuck. That nipple is pretty bad I tried to spin it to remove at it did a few turns really hard to grab.
  4. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Sticky in post number #4? of the main Force forum?
  5. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    So it's supposed to come out on eithwr side right? I will do it tomorrow
  6. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    I put it back and even without bleeding it stays put. So it should be right. But as I staryed to do the second engine the line that goes to the tilt cylinder broke off the cylinder. Wtf. The little part that's left spins and it might come off. I was trying to remove the cylinder by taking out...
  7. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Wanted to point out that there is a lip on the contact area and it is not flat with the surface so it will press against the seal. I hope that's the way it should be.
  8. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    In the link it showed flat side out for the little seal
  9. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Ok one done. I use a heat gun. Safer. The black are is tye old seal I guess.
  10. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    So they pop out not unscrew. Good to know
  11. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Check valves out. Where are these seals? How do I get to them?
  12. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Hey Jerry above for the leak from the top carb, when I prime it gas comes out I think from the bottom gasket, you mentioned the needle seat. Is that still available. I have the rebuild kit, don't know if it's in it. I was gonna open and cleaning adjustthw floats if need be. So the kits are...
  13. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    I got it could not understand why there's no seal inside the upper end between the impeller and the black cover. The drive is mostly done waiting for one of the water pump gaskets that I thought I had. Will do a leak test too. I hope there are no leaks to the inside anymore.
  14. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    OK I installed the gears and the shafts with retainers. I am at the cover and water pump case. the top of the black cover in the center where the impeller is has an opening. There is a robber seal in the picture does that go on top or inside the black cover?
  15. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    It actyally fit back pretty good and I hb welded it. That holds the o-ring in place. Should be all good now. Last night I did the forward gearupper shaft and bew bearings. Replaced all the needle bearings from the spool assembly and the 2 seals pmus big o-ring. Also on the plastic Cover I...
  16. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Here is the cover and the piece they go into each other. Don't know if it is broken or it goes seperately. It has 4 grooves that it fits in. Second picture shows the areaon the cover. Should I JB weld it together? Or silicone it?
  17. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    That's what I thought too. The cover has the o-ring on it still. I will show a picture in the morning. I haven't found another cover so am wondering if I can still use it
  18. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    So what tye heck is that platic hard seal looking thing. This is how I got it out right above the retainer.
  19. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    I am trying to locate the seal in yhe picture. Nothing in the diagram shows it. Have no clue where to locate it.
  20. G

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    It's attached to the gear. Is this the forward or reverse. It goes all the way in up to the shifter. I am watching a video of a guy doing the exact drive and it seems to be tye forward gear.
Top