Search results

  1. demarko210

    1976 Grady White Transom Rebuild

    Here is Poly. Got the transom resin and glued into place yesterday. I was a little concerned about mixing and making PB but everything seems simple. I didnt take any pictures because I got really interested using this resin. i spent 9 hours working yesterday. The transom has be glued all...
  2. demarko210

    Scarfing stringers

    I have been reading about doing different types of joints. Scarf joint has been the popular way of attaching new stringer wood to old. Everything that I am reading about doing joint on my stringers say when placing the joints together glue them with epoxy. My question is can I use thicken ploy...
  3. demarko210

    1976 Grady White Transom Rebuild

    This is what I was looking for and was going to ask how to do since I was not removing all stringers. The best way to bond the new core stringer to the old good section of the stringer.
  4. demarko210

    1976 Grady White Transom Rebuild

    maybe use some like this item C
  5. demarko210

    1976 Grady White Transom Rebuild

    Here is a issue i have. I have water in this area both sides and I wanted to ask how to prevent the water from building up in this area? Add a drain hole through the new stringer on each side? The foam did not prevent the water from getting in and it could not get out. the stringers are water...
  6. demarko210

    1976 Grady White Transom Rebuild

    I am still working on the boat. Here is a picture of the cap cut so I can use the chainsaw to get that wood out. I have been thinking of just making an inner skin and buying seacast and pouring it in. I have doubts about putting the transom in piece by piece like the image i saw in another post...
  7. demarko210

    1976 Grady White Transom Rebuild

    I have started the removal of my engine this month. With the nice weather we are having I may start to make my of the rear of my cap. I would like to get advice from those that have experience doing this work. I have been planning this for about 2 years now. I have attached pictures please...
  8. demarko210

    New piston rings

    I installed new piston and rings in my Mercury 110 now when I try to turn the flywheel it's very difficult and almost ripped the pull starter out. Can anyone help and tell me where to look it's a Mercury 110 serial number 318 XXX thanks guys
  9. demarko210

    Transom Wood

    Can I use this wood at lowes for my transom on my 19ft gradywhite? I also wanted to know if I remove my floor with out popping the cap with my hull warp?
  10. demarko210

    115 inline again 531??? distribute-less

    I am having a problem getting my boat of the ramp now. When I shift into gear the engine slows and cuts off. I have been reading this forum and everyone says to adjust the idle mix screw with the engine in forward gear. I am not doubting what they say and I will try this method but how do i get...
  11. demarko210

    Switch assembly

    On tell me what the Mercury switch assembly is used for? Part # 87-33386A 3.
  12. demarko210

    115 inline 531??? fuel pump

    My question is about the fuel pump, in my diagram I have 5 pieces to the fuel pump the five pieces are two gaskets,diaphragmm,cover ,and the base. However on my engine I still have 3 other pieces which are one gasket then a metal plate and then another gasket is attached to the engine. my...
  13. demarko210

    Transom Replacement

    When I replace my transom I will be doing it from the inside of the boat. I wanted to know can it be replaced in 3 sections instead of one whole piece? I have a notch transom on a Grady White boat. I wanted to cut the transom in 3 and bond it back in place. Because of room restrictions the 3...
  14. demarko210

    1974 Grady Weekender Transom

    My transom is water logged. When I place my finger in the upper parts of the transom where the motor bracket and ladder rest, it is soaked with water. I also notice from the inside looking out in the same location I can see light making it way through. Is there anything I can do to as a...
  15. demarko210

    115 inline 531??? choke

    When I press the button at the ignition the choke closes but after the engine starts it stays close. It use to open back up after i depressed the key. Can anyone tell me where to look?
  16. demarko210

    Mercury 110 9.8 rebuild hone cylinder?

    I am doing a rebuild because of low compression. I am adding new upper and lower bearing and seals along with piston rings. I wanted to know after adding new rings to the pistons is it a need to hone the cylinder?
  17. demarko210

    carburetor jets for KB11A mercury 110 9.8hp 318XXX

    Can anyone tell me where I can find some carburetor jets for KB11A
  18. demarko210

    Stator Mercury 115 6cycl 5314656

    I replace the stator on my motor now the engine will hardly start and when it does it will not stay running. The stator had an extra ground wire which i told was normal. The color code of the wires do not match what is on my switch box. The switch box ask for red and blue on the top and the...
  19. demarko210

    Mercury 115 6cycl 5314656

    I replaced the stator because the wiring was shot. I replaced it with Sierra International 18-5854. Now when I runs there bad miss somewhere. I can not get it to run long enough to check with my timing light. I want to know the new stator had an extra black wire that me original did not have. I...
  20. demarko210

    Mercury 110 9.8 3183164

    This is a pull start motor with spark and new points adjusted to .02 is very hard to get running. My question is, when I did a compression check it came out 60 psi both cylinders. Is this acceptable for a pull start reading? Also it is very hard to pull. I replace the rewind spring. The motor...
Top