Search results

  1. N

    Johnson 50 2stroke Starting issue

    The thread says Johnson 50 2 stroke. Modelnumber? Early 70.es (71 and up) loop charged "looper" OMC 50-55Hp was known as "explode motor". They shoot a hole or a crack into the crank case when the connecting rod or the piston broke. I have had some of those engines and sometimes it is hard to see...
  2. N

    Johnson control box

    Not knowing your control box but I would never go for a Chinese one. Buy a used OEM box instead. Most parts from China are crap.
  3. N

    1989 force 85hp shift pivot screw

    If the drain plug is hard to remove try to gently heat the area around and the plug with a propan torch or if you have a gas welding set up with oxygen and acetylen. The general way to fill the gear oil is from the drain plug. When filling from bottom you know that no air will remain in the LU...
  4. N

    Need Help Identifying an OMC Lower Unit

    I have a 50Hp 1989 Yamaha and this unit is very similar to the unit on the yamaha. I think OMC never use that bearing housing with a washer with tabs and a nut. Mercury and Force had that design. It is a Yamaha LU, difficult to see if is is 40, 50, 60 or 70Hp. Maybe a 90Hp?
  5. N

    Most common problems with 4 cyl / 3cyl chrysler outboards

    In my opinion 2 strokers do not want to idle for long times. The bigger engines the harder it is to idle for long times are my opinion. The advantages with those surface gap plugs are they are easy to clean from fouling. Just wipe them with a piece of rag. If you have clean the screens at the...
  6. N

    Most common problems with 4 cyl / 3cyl chrysler outboards

    One simple tips is to put a piece of rag at the bottom cowl just in front of the carbs when tilting the engine up. It will absorb the fuel, then pull it any when running the engine and then change it every time you tilt it up. I do not think there was an air silencer at the 4 cylinders as it was...
  7. N

    1988 50 hp force no spark?

    Please read the rules of this forum. Start your own thread, cause it is easy to mix the issues and what you have done when troubleshooting with the other one in the thread.
  8. N

    1974 9.9 Johnson running problems. I can get it started but then runs very ruff.

    First of all check compression and then for spark at both cylinders. Compression should be 100 PSI or more at both cylinders. Maximum 10-15% in different between them. Spark should jump 3/8 of an inch or more in atmosphere. If that checks out good pull the carb and clean it.
  9. N

    1969 85hp starflite, low power and cutting in and out

    That seams the culprit with your issue. Looks like the capacitors in the amplifier are bad. They dry out when old and you get lower output voltage from the amplifier to the coil. Have you check the coil? Bad insulation and it will fail when gets warm.
  10. N

    1969 85hp starflite, low power and cutting in and out

    Try to heat up the amplifier with a heating gun and check if it fails. Do not heat it up to much with the heating gun!! 135-140 dgr F (55-60 dgr C) is enough.
  11. N

    1988 force 85 hp throttle control box

    This thread is 13 years old and Frank A is not with us anymore. Start a new own thread. please.
  12. N

    1969 85hp starflite, low power and cutting in and out

    Not uncommon CD boxes, switchboxes and amplifiers fail after they are heated up. I have had these kind of issues at different brand such as OMC engines, Mercurys, Chrysler/Force and the japanees brands.
  13. N

    Cleaning drain passages

    No sealant at the surface at LU to midleg. Yes, the cavity where the shift rod goes is exposed of water. There is a seal for the shift rod where it goes into the gear case. You might be seeing the seal from cavity or not. Do not have in my mind right now if the seal is push in from the gear case...
  14. N

    85hp charger speed/prop/rpm concerns

    Generally going up or down one inch in pitch will lower/rise the RPM about 200rpm. Going from 19 in in pitch and 7000RPM to a 21 in pitch prop will end up at about 6500-6600RPM
  15. N

    85 force lower unit drain plug

    Have you check the terminal lugs for all the thin wires from the triggers? It is common that the wires break under the shrink tubes cause they are so thin.
  16. N

    85 force lower unit drain plug

    You can swap CD boxes and use the #2 output channel from box one (feeding #1 and #2 cylinder right now) to feed "3 cylinder. But you have to rewire the wires from trigger for "3 cylinder so they feed the second output channel for the CD box.
  17. N

    1988 50 hp force no spark?

    Nice to hear that our advice was succesful. Enjoy rest of the boating season.
  18. N

    Johnson stops dead!

    As my note in post #6, electronic components can fail when get old and heats up. I have had the same issues with at least 3-4 engines (Mercurys 7.5 and 9.8Hp in this case if I do not remember wrong.). As a roll of tumb is that electronic components lifespan is shortened by half if the ambient...
  19. N

    Chrysler 75hp, need direction.

    Set all air/fuel screws at 1 1/4,note the setting. Start the engine and warm it up. Start to turn the first (top) slowly 1/8 of a turn CCW, let the engine adapt the new setting (about 10-15 sec). Continue with this until it start to act up from to rich mixture. Note the setting and turn the...
  20. N

    1979 75 hp Chrysler motor CDI is screaming any suggestions

    Do the troubleshoot as per outboardignitiondotcom. Scratching the white/black wire to ground and check if you got spark from CD box without using the preamp. Check and clean the inside of the distributor cap. Check the HT wires from distributor to spark plug rubber boot. Check the battery...
Top