Search results

  1. N

    89 125 won't go into forward gear

    From my experience the clutch dogs and gears are sensitive to the adjustment and the edges can look pretty good with a small rounding BUT they do fail under load. I have answer to las thread about his issue and I have made the same journey as him with the LU of my 1977 65Hp Chrysler. Your 125Hp...
  2. N

    70hp Force outboard idles high and Bogs down with throttle

    If the diaphragm is bad you do not need to change the whole fuel pump. Just change the diaphragm and the gasket. There are fuel pump kits out there with diaphragm and gasket, both OEM or aftermarket.
  3. N

    Major two stroke screw up Force 120

    Like jerryjerry says, run it with the mixture you have. TCW-3 is the next generation of TCW-2 and the 2T oil for water cooled engines are made for lower engine temperature then air cooled two strokers such as motorcycles, moped, chain saws etc. Run with the mixture you have until it is time to...
  4. N

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Please you have to carmel down. Start to troubleshoot in a logical way. You are jumping all over, we are not able to give you advise when you do not work logical. No advise from me when you jumping all over!!!!
  5. N

    Chrysler 45 hp Model 457HH Questions

    Hello, this thread is 12 years old. Read the roles and start a new thread.
  6. N

    ‘83 Chrysler 7.5 replacement follower for carb throttle linkage

    Have you tried with Franz Marine? Otherwise as it is made of plastic try to glue it with Loctite super glue. They have a couple of different typs such as 401, 424 and 480 etc for different applications.
  7. N

    Force 125 ignition

    As CDI box #1 feed the #1 and #2 cylinder and box #2 feed the #3 and #4 cylinder I suspect the blocking diod in CDI box #1. The wire you disconnected for the stator is feeding #1 CDI box. If you swap the CDI boxes the spark at all cylinders will occur if you disconnect the #3 brow/black/blue...
  8. N

    105 water pump

    Stephenca118 I refurbish impeller housings by using chemical metal and fill the pithing with it. Then I sand it to a smooth surface and it works really well. A new impeller in that housing will work but not pump with full flow and the impeller will not last as long as it should.
  9. N

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Chrysler /Force engines has a spagetti seal at the split of the block, no paper gasket. When I do a rebuilt I either reuse the spagetti seal if it is in fairly good shape and add some Permatex Form a Gasket liquid gasket or I use a rubber string (looks like o-ring rubber) which is gasoline/oil...
  10. N

    Chrysler 65hp clutch dog problem

    Yes, you are right in your theory, good. You can try to resurface the clutch dog and gear and se what happens. Would be a good information for me too as I have one gear with rounded edges too.
  11. N

    Chrysler 65hp clutch dog problem

    Las, I do not know if I misunderstand you but the clutch shift rod will always be engage to the yoke even if you have a spring connected to the shift lever or not. This have no disadvantages for the function in my opinion. As I mentioned before all lager Chrysler/Force engines has this typ of...
  12. N

    Chrysler 65hp clutch dog problem

    Jerryjerry, the edges at my forward gear looked about the same and my thought was as you, it do not look so bad! As I had the LU disassembled I suggested to change the forward gear BUT I found that an adjustment of the lower shift shaft might have fixed it. I had a spare LU and put it on the...
  13. N

    Chrysler 65hp clutch dog problem

    Las, my experience is that all lager Chrysler and Force engine do not have any spring to hold the clutch dog/shift shaft in place when engage. It is just the shift cable ,shift shaft, gear pivo pin and yoke that hold it in gear. I suggest you to mount a small spring at the shift lever to give...
  14. N

    Chrysler 65hp clutch dog problem

    Las I have made the same journey with my 1977 65Hp in this summer. The gear started to jump out of gear at almost WOT and WOT and I did not countinued to run it. I disassembled it and found the edges at the forward gear rounded. The clutch dog edges was also a bit rounded so I flipped it 180...
  15. N

    Lower bearing carrier removal

    That screw holds the shift lever to the shift pin which is connected to the clutch dog and has to be removed if you want to pull out the prop shaft from the gear case housing.
  16. N

    Thanks for the help now a new issue (70hp Force) low top speed

    Check the link & sync at the top of this forum. Your engine is not set up correct. Frank A has a link & sync topic at this forum.
  17. N

    1993 Force 90hp

    With the LU off the engine you can shift it F-N-R? But when the shift rod upper connected you do not get forward? Is that right? Measure the total stroke of the shift rod from forward to reverse with LU off and then check the stroke with the LU mounted on the midleg.
  18. N

    1993 Force 90hp

    Can you shift it with the remote cables unhooked? Shift by hand at engine with the shift lever. You have to rotate the propeller when shifting by hand otherwise you may damage the shift rod/linkage.
  19. N

    timing issues on 120hp force outboard

    Do not set your timing gun to 32 dgr. Just leave it at zero and when you crank the engine with the starter. Aim the timing gun at the flywheel/timing plate and the 28 drg mark should line up with the zero mark at timing plate (throttle at WOT). If not, adjust the timing linkage with the screw...
  20. N

    Chrysler 7.5 no spark

    The ignition system contains a CDI box, a stator, a trigger ring and two ignition coils. First check all groundings for the ignition system. Outboardignitiondotcom may have troubleshoot chart for your engine. As you do not have spark at all, I would suspect the stator or the CDI box. The stator...
Top