Search results

  1. jerryjerry05

    150 Evinrude Ficht 2004

    Thanks
  2. jerryjerry05

    150 Evinrude Ficht 2004

    Thanks, New fuel lines, port motor=removed vapor sep. and cleaned it. New impellers both motors. New fuel lines and filters. Comp great, both motors. New oil lines and tanks cleaned. The boot strap tool? why would I buy that?
  3. jerryjerry05

    1977 Chrysler 10hp 100HA cowling

    Look for marine salvage yards. Antique outboards. There are yards all over the mid west. Here's one: https://forums.iboats.com/threads/salvage-yards-by-wilde1-verified.428012/ Hope it works Another one: https://www.facebook.com/groups/1739059919642568/
  4. jerryjerry05

    1956 Johnson 30 / Starter won’t turn flywheel completely

    Do a compression test? Dirty inside starter? Does the starter get hot? how about the battery posts and cables? If the bearings are corroded, that can cause hard turning too.
  5. jerryjerry05

    150 Evinrude Ficht 2004

    Twin 150 Ficht, both only go to 2500 and then cut out. Any suggestions or ideas? Any other repair forums or places ? The only place in the treasure coast area keeps putting the owner off, first appointment was Jan 10 then next week and again next week. ANY HELP would be appreciated. The owner...
  6. jerryjerry05

    1995 Force 50 Turns over, doesn’t start

    If your running in a tank? Make sure the water is deep. Needs to be 4 inches over the top of the cavitation plate. FYI If it's a 2 piece lower: then it needs special muffs for running on the hose. Using regular muffs can cause over heating.
  7. jerryjerry05

    1989/1990 4.3 distributor

    I put a piece of sponge with WD under the inner plate. Ten WD Silicone spray the housing Then replace every fall when winterizing.
  8. jerryjerry05

    1988 mercruiser alpha one water pump issue

    The direction of the vanes?? makes no difference. The impeller is it the same as the one you removed? They sell one(Force/Chrysler) that is just about the same size and when installed it pumps but pumps poorly. On the hose or in the water?? The hose might not supply enough water?? You replace...
  9. jerryjerry05

    1995 Force 50 Turns over, doesn’t start

    IF???? you have spark, however small it's probably enough. It sounds like the fuel system might be the problem. You have a primer that shoots a small amount of gas into the carb each time the switch is activated, holding the key in only gives 1 little shot of fuel. To test: unhook the hose from...
  10. jerryjerry05

    1985 85 hp force

    The 2 balls are the connection points for the ends of the shift and throttle cables. They take 2 special connectors. Both are available, Ebay has them. One ebay theif is selling the throttle one for 50$ If you get the controls, they sometimes come on the end of the cable?? I sent you a PM.
  11. jerryjerry05

    1978 Chrysler 85HP Powerhead Swap

    It's under the seal, did you remove the seal? I never saw that either. But I've never removed that seal.
  12. jerryjerry05

    1985 85 hp force

    Your choke picture won't open
  13. jerryjerry05

    Force 9.9HP 1991 outboard

    No where's near there.
  14. jerryjerry05

    1985 85 hp force

    See my post on the other site.
  15. jerryjerry05

    Force 9.9HP 1991 outboard

    Where you located?
  16. jerryjerry05

    Force 9.9HP 1991 outboard

    Is this your starter?
  17. jerryjerry05

    Force 9.9HP 1991 outboard

    Shift interlock rod not a cable :( #10 activates #1
  18. jerryjerry05

    Force 9.9HP 1991 outboard

    It could still be stuck. The cable locked?
  19. jerryjerry05

    Force 9.9HP 1991 outboard

    Sounds like the shift interlock is stuck??? Pic of the pull start?
  20. jerryjerry05

    Tachometer for 1974 135hp

    Get one and try?
Top