Search results

  1. R

    Evinrude Tilt Trim motor

    Is the drive coupling in place ?-----Does your system use a 2 wire ( green and blue ) or 3 wire ( green , blue and black ) on the motor ?----Is manual release valve tight ?
  2. R

    bravo III milky oil but holds pressure for days

    Install a seal kit now.-----Cheaper than gears and bearings.----Seals wear out and could be half worn now.
  3. R

    Mariner Idle Stabilizer - Spark Advanced Module

    Most folks would say to remove the idle stabilizer and throw it away as far as you can.
  4. R

    Possible water intrusion or lean sneeze?

    Off topic-----There is no head gasket on this Mercury motor.
  5. R

    Info on Evinrude 115 E115TLETS

    "Absolutely makes an injector oil "-----Explain what that means.
  6. R

    1978 700 series 70hp mercury high idle

    Motor slows down with choke because it is flooding.----I do not believe this is a fuel issue.----In my opinion it is a timing issue.
  7. R

    Info on Evinrude 115 E115TLETS

    New water pump impeller.----Test VRO if it is in service.----Test alarms.----Inspect the 2 thermostats / poppit valves.
  8. R

    1978 700 series 70hp mercury high idle

    Sounds like timing issues.----Too much advance at idle.-----Did you remove entire flywheel or just the flexplate to replace trigger ?-----You are sure that the splined flywheel is installed correctly ?
  9. R

    1978 700 series 70hp mercury high idle

    Serial # of this motor ?
  10. R

    Impeller kit number?

    The no oil warning module did not come out until 86 models.----An upgrade kit was available for 85 models.----But there is huge $$$ involved for new bits.----Used VRO units are " dime a dozen " in some areas.-----Take the time to get this right.-----Here I would go to a " parts motor > and...
  11. R

    Impeller kit number?

    The original 1985 VRO may not have had a " no oil " warning feature.----The VRO is a simple device.----Easy to take apart for inspection / testing.-----Post the compression test values before you spend any $$ on this motor.
  12. R

    1993 fast strike 150 carb jets

    Not the first one to make this mistake.------0322907 at about $40 each for 6 of them.----Don't worry about others.-----Why did you replace VRO?----What trouble shooting was done , if any ?
  13. R

    1st time buying old boat

    At $600 it looks to be a good deal if the motor is a 73 or newer.----Looks like that motor is older with electric shift and trouble some battery electronic ignition.
  14. R

    Info on Evinrude 115 E115TLETS

    Tested a 1990 low hr 90 HP recently at 130 PSI on my " known to be good " gauge.
  15. R

    1993 Johnson 150 -- grinding in reverse

    Shift rod adjustment will likely correct this issue !
  16. R

    1993 Johnson 150 -- grinding in reverse

    Some folks still think shifting slowly and easing these motors into gear is the best thing to do.-----WRONG.
  17. R

    1993 Johnson 150 -- grinding in reverse

    If it is grinding in reverse you need to look into shift rod height adjustment first.
  18. R

    Info on Evinrude 115 E115TLETS

    Shop carefully.----At 90 PSI / cylinder that motor would come apart for rebuild here.
  19. R

    Evinrude 1981 70hp 70tlcim - Intermittent Spark

    First thing I would do is load test the battery.----Take starter apart for inspection , cleaning and ohms check on armature.
  20. R

    Info on Evinrude 115 E115TLETS

    A crossflow model.----Not am E-TEC-----Do a compression test BEFORE you spend any $$ on this motor.
Top