Search results

  1. Bondo

    John Allmand - SuperNova19 video restore

    Hi f_in,.... Long time, no see,..... here anyways,..... I see yer posts at offshore occasionally,....
  2. Bondo

    Just curious

    Ayuh,..... It would probably blow oil outa the dipstick tube,.....
  3. Bondo

    Mercruiser 4.3 Repower Engine Mount Question

    Ayuh,..... The only way to know Exactly where the mounts have to be built is to hang the motor, 'n insert an alignment bar,..... Where ever the motor's mounts are when Aligned, is where ya gotta build the wood mounts too,.....
  4. Bondo

    Water leaking into bilge

    The trim hoses connect to the hyd. manifold, Right about where yer leak is,.... It unbolts from the transom housin', at the bottom,..... Go out to the boat, lay on the ground under the drive, 'n look straight up,.... You'll see where I'm talkin' 'bout,..... No need to pull the...
  5. Bondo

    Cabin Floor restoration, drain question

    Ayuh,..... Everyone of those compartments need a limber hole at the lowest point, boat at rest, so that any water that finds it's way in,.... Can drain down through the hull, to the pumpable bilge,.....
  6. Bondo

    350 mercruiser block

    Ayuh,...... The best way to go is with a 350 crate motor, or a pickup motor,....
  7. Bondo

    mercruiser 4.3 alpha 1 gen 2 shift issue

    Bump,..... I'm guessin' the lower shift cable needs adjustin', or replacin',....
  8. Bondo

    wont shift out of reverse mystery issue

    Ayuh,..... Welcome Aboard,.... It sounds like the shift switch is disconnected,..... The shift switch is on the shift plate, where the forward cable meets the lower shift cable,..... The neutral safety switch, is inside the controller,..... I'll move this to the Merc I/O forum, as it's a...
  9. Bondo

    Water leaking into bilge

    Ayuh,..... Where the trim hoses go,..??..?? If so, the gasket for the trim hyd manifold could be bad, or, possibly the transom housing is corroded through,.... The hyd. manifold bolts on from outside the hull,.... Unbolt it, pull it down, 'n check it out,....
  10. Bondo

    malibu 5.7 mercruiser

    Ayuh,..... Welcome Aboard,...... The Quadra-jet is a 4bbl. carb, 'n it sounds like yers seriously needs to be rebuilt,.....
  11. Bondo

    Mating Engine to Mercrusier problem

    Ayuh,.... You sure are,.... Everything you've said in this thread is Wrong,..... Welcome Aboard fordlove,..... You need an '87 or newer Chevy flywheel, that matches the diameter of the old motor, probably the 14", 168 tooth,..... or possibly, the 12" 153 tooth,... Yer old motor has a...
  12. Bondo

    Edelbrock 1409 woes

    Ayuh,.... The float bowels leak off into the intake,..... Ya, it's a problem,..... achris, as well as Rick Stephens have done extensive work with these carbs,.... There are fixes, 'n work-arounds,.....
  13. Bondo

    Yamaha L4 3.0 trim/tilt pump concern

    Ayuh,..... Never seen what yer drive uses for a trim pump,..... To test the motor, jumper right to the motor's wires from the battery,.... When the relays click, is there power to the outlet terminals,..?? You've got a test light, Right,..?? If a replacement is necessary, Sei sells an...
  14. Bondo

    Replacing mercruiser 485

    Ayuh,.... Look at the flywheel,.....'Does it have the threaded holes ya need,..?? If not, then youl'll have to swap the flywheel as well,.....
  15. Bondo

    Replacing mercruiser 485

    Ayuh,.... Whatever is Necessary,.... Please keep yer questions in this thread,.... I deleted the other one you started,....
  16. Bondo

    Engine replacement

    Ayuh,.... Michigan motors has been used by many posters here,....
  17. Bondo

    Engine replacement

    Ayuh,.... Go with a Long Block,..... Doin' a bare block is a fool's errand,....
  18. Bondo

    2.3 ford OMC no spark

    Ayuh,.... Welcome Aboard,..... Is there voltage at the coil's (+) terminal with the key "On",..?? Do the points arc when you open, 'n close 'em manually,..??
  19. Bondo

    350 cracked block

    Ayuh,.... Welcome Aboard,...... A crate motor, or truck motor will be fine,.... A fire breathin' hot rod motor, not so good,....
  20. Bondo

    Advice needed on sterndrive replacement

    Ayuh,.... Nothin' wrong with an SEI,.....
Top