Search results

  1. Scott06

    2012 3.0L TKS runs great with muffs, but slow on lake...

    Yes I know you had spark , but when it wont run verify it again to determine why it went from running to not running. yes dribble some down the carb to see if adding gas changes things. Also as all dodge suggested look down carb bores when you shut it off to see if bowl is over flowing and...
  2. Scott06

    Milk in reservoir, not in outdrive

    Are you still using the same cap? is water getting in from above sunpad etc? What lube are you using Did yo check the from the bellhousing to the transom there is a 1/4" or so rubber hose. drive could be passing pressure test but getting mositure in that way. Is this contamination in the line...
  3. Scott06

    2012 3.0L TKS runs great with muffs, but slow on lake...

    I think when it doesnt restart take a spark gap tester see if you have spark if you do dribble some gas down the carb , if it restarts then you are missing gas. Just gotta figure out if its spark or fuel. Hard to tell form the keyboard but if yo have good spark and timing is right it should fire...
  4. Scott06

    2 Stroke Oil Thread

    That is about what I was running my old Evinrudes on. Almost zero smoke and very clean plugs. Had a 1975 15 hp , and a 1973 9.5 hp kicker. I looked it up again. It was in the 1980's that Evinrude labeled the 15 hp and possibly others for 100:1 for a short time and discovered they had issues...
  5. Scott06

    2 Stroke Oil Thread

    I started running amsoil in our old evinrude 2 strokes...
  6. Scott06

    1979 Starcraft American Offshore 22’

    Yeah see that now , didn’t think they made FG boats back in 79. Just the usually stringers and transom on glass boats of that age
  7. Scott06

    1979 Starcraft American Offshore 22’

    what is the powertrain in it OB or IO? if IO certainly look at the bellows. Both will need impellers replaced. If I recall older starcrafts would get cracks on the chine, may have been models earlier than yours. Also can leak at the rivets.
  8. Scott06

    28' Pontoon with 3.0 Mercruiser Prop

    the sharrow threads make me miss the oil threads...
  9. Scott06

    alpha 1 gen 1 noise

    Split the halves to see if it can be isolated upper and lower - at this point you are into tearing it down to see what the issue is- most likely a bearing if the gears are ok. You cant get very far into the drive with out some merc specific tools , which is why folks generally get a SEI drive or...
  10. Scott06

    Need help reinstalling choke linkage (Mercarb 1389-9562 carburetor)

    thats the accelerator pump lever. you will have to take the top off the carb and there is a set screw holding to to the pump inside the carb. the smaller rod uses a small cotter pin or clip to hold it on. Mikes carb parts has some god videos of mercrab rebuilds not sure if its on his website...
  11. Scott06

    thinking of a Delco EST ignition system conversion but have a few concerns....

    If you can still get good sets of replacement points I wouldn’t spend the money for the delco. I filed and gapped a set of points this spring on a 1973 evinrude, runs like new now ( also rebuilt the carb). From the looks of them and the amount of rubbing block wear they are probably original...
  12. Scott06

    alpha 1 gen 1 noise

    pull the drive check the gimbal bearing first, as by the mouse I’m thinking that. If that is ok drain drive lube and pull the top cap. See if metal is in the lube or water
  13. Scott06

    Need help: Bizarre Bravo III freshwater galvanic corrosion quandry

    I was surprised at how much more ‘active’ the oem ones were Vs aftermarket. Of course this is a sample size of one…funny thing is seeing ADs comment about aluminum is I took off the AL ones that were on there, PO used this boat in brackish bay areas of Deleware. it was my understanding via word...
  14. Scott06

    Need help: Bizarre Bravo III freshwater galvanic corrosion quandry

    not sure where you get your magnesium annodes from, but I also had some corrosion on a fresh water alpha gen 2, Lift kept and there is no shore power to it. My hoist runs of 12 vdc. I run a revolution 4 prop which is a big chunk of SS. I added a mercathode, still getting some bubbling around...
  15. Scott06

    Loosing Faith in Humanity . . .

    Also plan on getting a tax document from ebay. I so,d a machine from work on my eBay acct ended up getting a 1099 or similar for $8 from ebay …
  16. Scott06

    2012 3.0L TKS runs great with muffs, but slow on lake...

    usually the fuel line is 3/8" double flare like brake lines would think you can get a coupler and a short section of line cut in half & use some 3/8 ID hose to splice in your T for the gauge The TKS uses an enrichment module (valve) to richen the fuel mixture until the engine warms up, it...
  17. Scott06

    2012 3.0L TKS runs great with muffs, but slow on lake...

    At this point I would test the fuel pressure on the water at the rpm where you feel like you are hitting the wall where it should be doing better. if the float wasnt cracked its probably all right. Mikes carbs had at one time brass floats for mercarbs not sure if TKS is the same thing. the 3...
  18. Scott06

    1997 Mercruiser 4.3 LX not running steady steady at idle or higher RPM's

    Yes the advance knob should compensate so the light hits on the tdc mark -say you want 8 deg BTDC set the knob to 8 should offset the light to flash on the tdc mark. Also can be used to test total advance which is also important
  19. Scott06

    28' Pontoon with 3.0 Mercruiser Prop

    Google prop slip calculator you put in pitch rpm and mph it compute % slip
  20. Scott06

    2012 3.0L TKS runs great with muffs, but slow on lake...

    I saw new fuel pump but was fuel pump pressure measured under load ? my other hobby is old cars - its a chronic issue with mechanical fuel pumps these days - the pressure output is all over the place, even on what was historically considered good brands
Top