Search results

  1. alldodge

    What rifle to scope for hunting?

    Your mixing comments. I don't want a class 3, never did
  2. alldodge

    Some questions regarding Jeanneau Leader 8

    No the duck bill valves are inside the toilet. Look at the parts breakdown
  3. alldodge

    Some questions regarding Jeanneau Leader 8

    All toilets have what's called duck bills, which are one way rubber valves. They allow stuff to be pump thru one way but should seal off for the return. If the duck bills leak then stuff comes back into bowl It could be your onboard holding tank is full and needs to be pump out. If your in...
  4. alldodge

    Some questions regarding Jeanneau Leader 8

    Will take a guess at the switches, seeing the boat is made in France. With master key listing Batteries/Breakers, This one turns main power ON Bord = Edge so maybe shore power Domestic = so maybe onboard Negatif = Negative in english, on/off grounds Moteur = Engine in english, on/off power...
  5. alldodge

    Out to lunch Gear Oil Prices

  6. alldodge

    Replacement Prop Selection

    That helps Type 3 blade Pitch can normally be found on the hub either actual pitch or part number which will provide the pitch Speed 32 MPH RPM 4000 Your motor can be one of 2 types being a 1989 model. Most would turn 4200-4600 RPM. If your motor has a roller cam (noted with block code CD...
  7. alldodge

    Replacement Prop Selection

    Need some numbers to determine props What type and pitch is on it now? Current WOT speed using GPS? Current WOT RPM?
  8. alldodge

    water pressure vs air pressure

    I use shop vac on AC condensate line every other year.
  9. alldodge

    Force clamp screw bolt thread size?

    Just to make sure we're talking the same thing, a 5/8 bolt will have a 3/4 hex head
  10. alldodge

    Lewmar 700 pro series anchor winch

    I've had a Formula 27PC with 125ft all chain, and currently have a 280 Chap with 15ft chain and 185ft of rode. The all chain never had an issue with it going up/down. The Mix seems to always have problems going up/down. The rode hangs going out and more so coming in. I cut off 50ft of rode...
  11. alldodge

    Lewmar 700 pro series anchor winch

    Think your issue will be is the anchor locker deep enough? Most need 12 inch drop to top when all rode and chain is loaded
  12. alldodge

    What rifle to scope for hunting?

    Only those with class 3 license
  13. alldodge

    water weeping thru hull

    If the water is coming from a area that caught some water and now that it's on the trailer is leaking down, then no issue If it's leaking out of the hull/stringers then that's bad. It won't completely dry out and mold will start. After mold starts it has to be cut out to stop it
  14. alldodge

    Another prop slipping thread

    Never tried aftermarket but others have and have not heard of problems
  15. alldodge

    Need 78-84 3.0 181 CI OMC engine wiring diagram

    Welcome This is one I have
  16. alldodge

    Alarm sound when turning the key - starter does not work.

    With a 280DP that's a stern drive. The prop is attached at the stern hence the term stern drive. Inboards have a straight shaft coming out of the boat like a ski boat or large cruiser. Prop is under the boat instead on coming out the stern To check for a good ground connect meter and set on...
  17. alldodge

    Another prop slipping thread

    Don't know about coupler integrity, but I've never had one fail if it was checked yearly. Didn't matter if it was a 4 cyl or up to a 530 HP BBC Did have one burn up in my early years when I didn't check yearly Post a want to buy in the Offshore only section.
  18. alldodge

    Alarm sound when turning the key - starter does not work.

    I would not pay much attention to the alarm right now, stay with working on the no crank. You could disconnect the oil pressure switch right now until the other issue is found With the melted wires I would guess there might be a blown fuse, or the fuse was bypassed or wrong size installed. If...
  19. alldodge

    Another prop slipping thread

    I would say it must be the coupler has stripped. Would feel better if you smelled burnt rubber after it happened Don't think the BB coupler will fit, but never tried. They do make a steel coupler but all that means is the splines are steel instead of aluminum. Both use molded rubber to attach
  20. alldodge

    HOW TO FILL POWER TRIM ON 1982 50HP MARINER NO RESIVOR ON PUMP INSIDE OF BOAT CYLINDERS ON EACH SIDE OF MOTOR

    Looks like BWR1953 in post 7 has the answer The trim pump is not part of the motor, it's mounted on the boat hull
Top