Search results

  1. alldodge

    A ghost is stealing my anchors...

    Might be something as simple as a small stick, rock, some grass or weeds in the mud. As its dragged along its pressed open just enough so when the rode starts to come up it slips off. No way of knowing without watching I lost an anchor with similar type hook a whole bunch of years ago. It...
  2. alldodge

    A ghost is stealing my anchors...

    Snap hook and anchor do not go together. Takes very little to press in on the snap and release the anchor. If you don't want to store the anchor where the rode is, then just use the screw pin shackle
  3. alldodge

    help with iffy gas?

    For the most part, once gas starts going bad, adding fresh to it just makes more bad gas. All the additives IMO are sales gimmicks, other then things like Satbil which is used before it goes bad Differing opinions will be along shortly
  4. alldodge

    Recommendations for cleaning bilge?

    Use some dawn and sprary more water in. Let it slosh around some and drain it back out. Might need to do it a few times. Rag on a stick might help get the hard to reach spots
  5. alldodge

    2015 Mercruiser 4.3L TKS - Engine stall after 30 minutes; Unable to restart at 1/4 throttle

    Having it at the shop I'll assume they had it running on a hose at idle and it did ok? Need at least 1/2 throttle and later would idle, I would lean toward the carb was flooding. Might have had a spec of crud in the needle seat and it sitting for some time, it dislodged and starts working ok...
  6. alldodge

    Mercruiser 2.0 170 inboard starter engine done?

    I would put it back together and use it as core for another one
  7. alldodge

    2003 Merc 5.0 MPI no start, intermittent spark

    5V low will be one of the 5V sensors. With key ON disconnect them one at a time until you find the one pulling it down.
  8. alldodge

    Ran amazing then shake no thrust

    Cable is good, carb is empty of fuel due to other pumping of the throttle Now were back to the motor and drive, bummer
  9. alldodge

    Ran amazing then shake no thrust

    Ok, need to replace the cable, shifter or both The good news is the motor and drive is fine
  10. alldodge

    Ran amazing then shake no thrust

    The question is, Does the carb throttle plate move full open when the throttle handle is moved full forward?
  11. alldodge

    1987 MerCruiser 3.0 Flywheel size

    The 14 inch flywheel will also use a starter with staggered bolts The 12 3/4 uses a starter with inline bolts
  12. alldodge

    Bigger now bolt.

    The drotto system removes both of the hooks you have now and replaces it with just the auto hook
  13. alldodge

    Merc Bravo 3 prop shaft seal....

    Its a snap ring, but does not have holes so SR pliers can not be used. If memory serves it just takes a small screw driver
  14. alldodge

    Boat hit 200 degrees engine temp

    Probably, and that's where you start looking
  15. alldodge

    Merc Bravo 3 prop shaft seal....

    Once the retainer (item 38) is removed both axles will come out. Will need to remove a retaining ring (item 32) and they will separate https://www.mercruiserparts.com/bam/subassembly/30973/5398/130
  16. alldodge

    4.3 Mercruiser Power problem!

    Lets start with the motor serial number? Also is this a new to you boat, or has the problem just started? Can be many things, most of these are fuel issue or low compression
  17. alldodge

    Merc Bravo 3 prop shaft seal....

    Removal is easy enough for the small shaft, the larger one is a bear but can be done. A press is best to install the seals. I used the old small seal and placed on top of the new small seal then a hose clamp to keep them from separating doing install That is the correct seal kit
  18. alldodge

    Merc Bravo 3 prop shaft seal....

    The shaft has to come out and its not as hard to remove as the outer seal. Here is my link where I did it https://forums.iboats.com/threads/looks-like-im-getting-into-bravo-outdrive-repair.617342/page-2
  19. alldodge

    Mercruiser ECM replacement?

    look at the dipstick and see if oil is high or its milky
  20. alldodge

    Mercruiser ECM replacement?

    If boat sat for long periods in a humid environment, might not be so bad
Top