Search results

  1. alldodge

    1997 3.0XL carb rebuild kit

    Looking for the motor serial number. If we know what kind of carb then we can make a good guess at the kit number Might be a 2GC, Merc, other or TKS
  2. alldodge

    Mercruiser 5.0 50 degrees at idle

    For the timing to be 50* advance either the balancer has moved or your using the wrong plug to set timing (Ford/Chevy thing, Chris post 4). Only way I know without taking the head off to find exact TDC is with a stop bolt.
  3. alldodge

    Mercruiser 3.0l TKS stalling

    Right now I'm not worried about a small drip because its all in an interpretation of what your seeing. As air is sucked in pass the venturi the low pressure sucks fuel out of the carb. The higher the rpm the more fuel is sucked out. Depending on how clean the carb internal channels are will...
  4. alldodge

    Regal Commodore 2665 5.7OSXI, engine will not start, making NO turn over noise when turning key.

    Need more info and agree should be in VP area Might just be a bad starter When key is turned, the starter bendix or solenoid should push the gear into the ring gear. If this isn't happening, then may just be a stater issue, or wiring
  5. alldodge

    1997 3.0XL carb rebuild kit

    Best way to know what kit is with a serial number Next best is contact Mikes's carb. He will fix you up right and if its not right when you get it he will make it right https://www.carburetor-parts.com/
  6. alldodge

    Mercruiser 5.0 50 degrees at idle

    Balancer may have slipped To verify may need a piston stop bolt
  7. alldodge

    Mercruiser 3.0l TKS stalling

    Those are the venture's and a little drip is no issue. From your symptoms your most likely getting to much fuel so its flooding a little. This can be from a piece of crud getting in the carb needle seat, or just need to re-adjust things. The enrichment module is not the overall cause, because...
  8. alldodge

    Mercruiser 3.0l TKS stalling

    Yes, but most likely there is carb problems
  9. alldodge

    Mercruiser 3.0l TKS stalling

    No not normal, might need cleaned but may need replaced. Remove it and check measurements cold and warmed up
  10. alldodge

    Trailer bearings wear out ultra quickly.

    Check this one out https://www.boattrailerparts.com/Galvanized-Boat-Trailer-Axle-95-inch-3500lb-Square-by-Dexter_p_855.html
  11. alldodge

    Brand New Boat Owner!

    The outboard key has a feature that when pushed in a solenoid is energized on the motor that chokes the carb. As long as it is pushed in the choke stays closed Wiring for the key
  12. alldodge

    5.0 mpi backfiring through exhaust. Won’t start

    The cap should have the ports numbered, and left bank on left (1-3-5-7)and right on right (2-4-6-8). Makes it easier then the round ones Key ON pump should run for 2 seconds. Use a rag and push in on the schrader valve on fuel rail and see if fuel squirts out. If no gas, turn key ON/OFF a...
  13. alldodge

    5.0 mpi backfiring through exhaust. Won’t start

    No they are different. Boost pump is a low pressure pump at the fuel filter, and high pressure is under the motor port side
  14. alldodge

    5.0 mpi backfiring through exhaust. Won’t start

    Woops ok you have the additional boost pump
  15. alldodge

    Analog to Digital

    Being a 1990 I don't think the motor would be compatible unless its been replaced with a newer model. But if there is @dingbat might know
  16. alldodge

    5.0 mpi backfiring through exhaust. Won’t start

    My guess is the PO knows something he's not saying, and the Bravo does rotate in either direction What's your serial number?
  17. alldodge

    2014 3.0 mpi want go over 2500 rpm’s we have Cleaned all injectors replaced distributor and idles fine just will not go over 2500 like it’s on a rev.

    yes Disconnect the in-gear switch and see if it stops
  18. alldodge

    FLYWHEEL HELP!!!

    Looked up both I/O and IB 5.7 for 1996. There are different flywheels, and they both weight 33 LBs. The bell housing does show the IB starter comes in from the rear, all parts can be obtained today If you look at the side views of the 2 it sure looks to me like the ring gear is just on the...
  19. alldodge

    FLYWHEEL HELP!!!

    You built a 1996 motor and I know the 96 flywheel doesn't use a groove
  20. alldodge

    FLYWHEEL HELP!!!

    You sure about that? All other rings are installed by getting the flywheel cold and the ring hot. They don't move after that, easy peezy Hey @Bondo or @Scott Danforth
Top