Search results

  1. R

    03 mercury 50hp 2stroke loss thrust

    The clicking is normal.----Nothing wrong there.---Check for spark on all leads.-----Do a compression test for reference.----Install another prop and test run.
  2. R

    Sticking solinoid?

    Replace the wee ground wire on the solenoid ?
  3. R

    20hp Johnson 1983 - Push Button Start Wiring

    From the solenoid battery + side you feed 12 volts to your push button switch.------From the push button switch you go to one small post on the solenoid. ---From the other post you go to one spade on the neutral ( white plastic ) safety switch.----Note the safety switch only needs ONE WIRE !!
  4. R

    JW-10 will start, then die.

    Look through the inspection hole in flywheel.-----Inspect coils , clean and set breaker point through that hole.-----In my opinion hard starting is usually due to weak spark.-----So does spark jump a gap of 1/4" on a test device.----Do not trust inline testers with a glowing light !
  5. R

    1986 Johnson 150 J150TXCDC Gearcase Seal Replacement

    If it holds those pressures it is all good.---Fill with the best BRP specified oil for it and go fishing.
  6. R

    Sticking solinoid?

    Agreed it could be the wrong solenoid.----Simply because the parts counter clerk and the buyer do not know that there is a difference.------And the model # of the motor is still top secret.
  7. R

    Gear case hole?

    Is there any water getting in your gearcase ?-----And some oil leaking on that outboard might be normal.-----It would be the oil that is mixed with the gas !
  8. R

    Short to Long Shaft swap on a 1995 20HP

    One issue is that sometimes the castings are the same.-----Then on some model they use bigger bolts / locating dowel / bigger threaded holes.--- than previous model.---This part would then have a different part # but can be used.----You could easily modify these parts.-------A good shop ( if...
  9. R

    1974 Evinrude 25hp wont run.

    Is the magneto plate bushing loose in the plate.-----Believe it or not if bushing is not lubricated it will wear from vibration during every minute that the motor runs.
  10. R

    Sticking solinoid?

    I can not see what you are doing.----Perhaps clamping the solenoid so tight that it is jamming it.-----I was not there !----Model # is ??
  11. R

    Sticking solinoid?

    So what motor is this ?---
  12. R

    1995 Mercury 40hp 4cyl - sputters and eventually dies at idle under load

    check flywheel key ?
  13. R

    Flywheel occasionally locks up

    See post #7 for reference.
  14. R

    1970 4 hp Evinrude stops suddenly

    The company / shop where i used to work makes precision parts.------Can hold tolerances of +- 0.000020"( 20 millionths )-----They now gets drawings in with an extra note.------Says " no materials sourced from China allowed in the manufacture of the product "
  15. R

    Short to Long Shaft swap on a 1995 20HP

    The swapping of parts gets into fine details.------You might have to pull the powerhead to install the longer exhaust housing.----You might have to pull the gearcase apart to install a longer driveshaft and shift rod.
  16. R

    1976 Johnson 70hp will only run low rpm after warming up.

    You might find that 5/32 ID is the right hose.-----And use ty-wraps made for hose.
  17. R

    Evinrude Mate 2 HP Driveshaft

    Good used driveshafts are not hard to find.----The same shaft was used year after year.
  18. R

    1974 Evinrude 25hp wont run.

    We get all these arguments from some folks.----Put the driver coil in the correct position and test run.
  19. R

    1974 Evinrude 25hp wont run.

    Coils can not be just installed like a sparkplug.----There is a factory tool to locate them in the correct position.---Agreed---- I think driver coil appears to be interfering.
  20. R

    Short to Long Shaft swap on a 1995 20HP

    find-----bay manufacturing-----They may offer a kit.------Around $450 I think.
Top