Search results

  1. alldodge

    TBI 260 Wont Idle When Warm - Will Run other RPM

    Agree, start with fuel pressure test Don't start replacing parts until we know what is causing the issue What's your motor serial number?
  2. alldodge

    wiring slave solenoid

    You said using a 1/2 breaker bar, that is enough to snap the bolt if its stuck. A 3/8 short ratchet would be ok. Best to use the belt to turn it with plugs out Do agree, if your going to rebuild, take it all apart and have the machine shop tank it. Depends on how much your going to do, but...
  3. alldodge

    alpha 1 gen 1 reverse lock

    Yes, I was talking about the shift cable. Didn't think that would do it but your issue has to be the drive or cable Your not going to damage the shaft seal by putting the 2 halves together even if its off one tooth. As BT mentioned, the drive should slide completely together and not need...
  4. alldodge

    alpha 1 gen 1 reverse lock

    Normally it would only happen in one direction. Since it was working fine before impeller replacement, this is what I would check first along with if the cable is attached correctly and not broke
  5. alldodge

    Outdrive leak question

    The list does show 7-10 first and is a good test. Over time there has been many discussions on this topic after Don had passed. These discussion is also where the slight vacuum came in. While it should not have leaked, it did. Try with 5 psi and see if it leaks
  6. alldodge

    alpha 1 gen 1 reverse lock

    The shift foot may be one tooth off when the halves went back together Lower locked counter clockwise Upper shift foot facing forward when the two halves are slid together
  7. alldodge

    Kill switch

    With the lanyard in the switch you want to use the 2 contacts which are connected. With the lanyard pulled those 2 contacts should be open. Connect to the purple wire after the key Don't know which switch, but its probably setup for twin motors and can just use 2 of the contacts for one
  8. alldodge

    Swarm

    Walking back from the shop yesterday I heard a humming. The closer to house I get the louder it gets. Walk a couple steps into the woods and level increases. Never saw what it was but turned around and walked back out. I'm thinking hornets because of the lower drone pitch. About 30 minutes...
  9. alldodge

    Need 4 wire tilt/trim switch

    Well learned something new, thanks. So it has a built in bypass wire
  10. alldodge

    1996 Wellcraft Eclipse Gear Issue

    I would say your issue is in the throttle handle. There are 2 cables and the internal mechanism is not working correctly. Needs repaired or replaced
  11. alldodge

    Outdrive leak question

    Have not seen the issue with cold, but your testing pressure is to high. Better to use 5 psi, and no more then 10 (5 to 7 best) The lip seals face inward, so the higher the pressure the tighter the lip is pressed against the surface. Also goo to test with a vacuum gauge if pressure holds...
  12. alldodge

    2008 Rinker Captiva 226 dash wiring diagram

    Merc uses standard colors
  13. alldodge

    New 5.7l Vortec safety oil pressure switch for electric fuel pump issues.

    There is a connection which is not good. Think of the issue as a water hose with a restriction. Somewhere from the beginning to the end (meaning the ground back to the bat) there is some corrosion. It could be a contact in the 10 pin connector Start post Red to 50 amp 50 amp Red/Purple to 10...
  14. alldodge

    Need 4 wire tilt/trim switch

    Not going to find a single switch that can do both functions with current wiring configuration. There is only 3 wires. The trailer function bypasses the trim limit on the drive The drive limit switch disconnects the up connection when limit is reached. The trailer uses the same wire from the...
  15. alldodge

    Basic Depth Sounder - Recommendations

    Not bad, Seams the only manufacture with a shot thru hull, and under 200 (Carid) isn't bad either Thanks, need one for my Rinker
  16. alldodge

    wiring slave solenoid

    If the outdrive has not been removed, then do remove it. Turning the motor using the crank bolt is a way of snapping off the bolt
  17. alldodge

    Shifting issues related to electrical wiring

    Tan/Blk or Brn/Blk I would still think of it as the alarm wire
  18. alldodge

    Basic Depth Sounder - Recommendations

    I like a fast digital read out when pulling into a new cove
  19. alldodge

    Duel outdrives - port stearing moves port to center. starboard moves both directions?

    There should be a tie bar inside which tie both drives together. Post a pic of the steering behind the motors
  20. alldodge

    Basic Depth Sounder - Recommendations

    I need to replace the digital Lowrance 2500 and many are using the 3500. Then others use the 3800. The issue is no thru hull transducer. I keep thinking about getting one and use rtv to glue it to the inside of the hull instead of hanging it off the stern. My Garmin chart plotter comes with...
Top