Search results

  1. R

    Johnson TN26 coil

    Likely need to adjust the coils to set the air gap on them !!
  2. R

    Johnson 9.9 Hard to turn over after rebuild

    First thing I do after tightening the crankcase screws is turn the crankshaft to check for binding.-----When you work carefully and with experience there are no surprises !
  3. R

    1977 vs 1978 Evinrude

    Parts worked the same way----Mounting of the pieces changed.
  4. R

    OMC 400 sterndrive with 15 spline prop shaft

    The 60E would make it a Bracebridge area boat.-------If it planes quickly you do not need a 13" pitch prop !!------evinrudeparts.ca----In your area can help you.
  5. R

    1985 Mercury 85hp (4 cyl) runs great for 20 minutes then boggs down

    Look for issues with water leaking into one of the cylinders.-----Have you changed out the water pump impeller recently ?-------Checked fuel pump diaphragm and the check valves in the fuel pump ?
  6. R

    understanding idle on 1971 Johnson 50 hp

    Good luck with your motor !----Post #1 indicated you were struggling.-----But obviously you are well versed on your motor now.
  7. R

    Retiring my Johnson '71 25hp

    Those are the best motors to own.----Parts new and used are everywhere.----Your location ?-----It should be an easy fix.-----And no point talking to a big shop as they are not interested in small jobs.-----They get plenty of work / revenue from $50,000 boats and big spending owners.
  8. R

    Shop manuals - are they really different from year to year?

    From about 78 to 92 they are essentially the same !!-----Same crankshaft from 74 to 2007 I believe.-------A 74 lower unit fits on a 2007 model, not the same internally but will bolt on.-----Same water pump kit from 74 to 2007 models.
  9. R

    90hp Shift Rod Height

    21-27/32"
  10. R

    25 hp runs on one cylinder

    Your location ?
  11. R

    Help me understand Power Tilt-Trim differences 74-90

    The newer integrated system will likely not fit on 77 and older models.----Unless you change a lot of parts !!!!----Like transom brackets and swivel bracket.
  12. R

    1977 vs 1978 Evinrude

    Well----1973 V-4 powerheads were a ---" one off year "----Not so much the 77 models.----They did make midsection changes in the 77 / 78 model years .----And they started offering the 25" extra long shaft models.-----Crankshaft center bearing was beefed up in the 79 V-4 models.
  13. R

    Help me understand Power Tilt-Trim differences 74-90

    Why ----They had to quickly come up with a system since trim / tilt suddenly became a big seller.-----Then they redesigned it to hide it in between transom brackets.-----Nothing to it and not a mystery at all.
  14. R

    Help me understand Power Tilt-Trim differences 74-90

    Some of the early ones came from factory with trim / tilt.------The early integral systems came with a 3 wire motor and later ones were a 2 wire motor.
  15. R

    Johnson 9.9 Hard to turn over after rebuild

    Something is wrong.----You did fit the center bearing on the dowel ?----And the upper bearing pin in the recess in the block.-----Best to take it apart again before you do $$$$ damage.
  16. R

    Tubing, vents???

    Nothing to do with RPM of the motor.----The bore of the hoses is just too small to allow significant airflow !!-----If you have engine running issues then post compression values here.
  17. R

    Evinrude 9.5 1971 3 blade prop to 2 blade what’s the difference??

    The 9.5 HP might rev too high with the lower pitch of the 6 HP prop.----You might damage the motor and go slower !!!
  18. R

    Evinrude 35 parts to 30 conversion

    The 1980 model might be crankshaft rated while your 30 HP might be propshaft rated.---Research required
  19. R

    Temperature switch circuit 2000 Johnson 150hp

    Pulse limiter is a ----Flow fuse----For the VRO-----Prevents damage from too much airflow or pressure spike to the pump.
  20. R

    Should water be ejecting?

    You should replace impeller if you do not know how old it is !!!
Top