Search results

  1. alldodge

    Where do you get your boat news?

    OSO has two guys which post new things happening in the boating industry as they come out. Mostly from speed on the water but also some regular stuff
  2. alldodge

    Mercruiser 228 Refresh

    It all depends on how and where it was stored. Being in a dry place like a garage would be best, but if outside under a tarp or near salt water are things that could cause more concern If there is any gas in the tank it needs to be removed and tank cleaned. Fuel lines replaced with USCG type...
  3. alldodge

    Help with DPS-B 1.95 outdrive

    Since your pulling the injectors, you going to have them flow tested along with cleaning?
  4. alldodge

    PWC's on the ohio ideas

    It can be shallow on KY and Barkley lakes even in the summer. Lots of rock and know how to read the markers. Must have a depth finder and go slow if unknown
  5. alldodge

    350 Mag MPI Horizon died at sea, cannot find the problem.

    Qbhoy, Agree they can go bad without warning but I have heard of no other which has needed to replace that often
  6. alldodge

    Sea water pump

    What you could do is disassemble the pump before buying parts. Could be it just needs a new seal and not shaft and bearings. Thinking the seal should not have come out unless there is a problem, so probably needs them but always good to check
  7. alldodge

    Sea water pump

    I like it, and looks like the bearings a sealed so no need for grease Also he notes that using just a automotive pulley remover/installer is all you need, but he used a press.
  8. alldodge

    Sea water pump

    Need to rebuild the pump, it has already lost most all the grease which was inside behind the seal. Need bearings and new seals kit 8M0140001 The pump housing needs to have a inner and outer stainless steel wear plates installed...
  9. alldodge

    Mercruiser 228 Refresh

    Howdy The older S/N don't come up by entering, they have to be found by looking at the number and comparing to the range This should be your motor. It comes up as a 260 but wouldn't worry to much about that unless parts don't come up as seen...
  10. alldodge

    Painting a new transmission

    Don't forget to protect against galvanioc corrosion. Guessing your going to use steel bolts to mount the trans and motor together. Look for dissimilar metals and coat surfaces and fasteners accordingly
  11. alldodge

    Rub Rail Restoration??

    Looks like similar rail which I removed. Rivets to hold rail on, and under the rail there are probably more rivets holding the top on
  12. alldodge

    Toilet Installation Mishap . . .

    Looked at my Kohler's in current house (installed maybe 6 years ago) and I can get my finger tip between tank and bowl
  13. alldodge

    Gas leak gas freezeing

    That's cool but, it says super cooled (-10*) and list done quickly Standard freezer inside a styrofoam cooler, don't get the cooler in a freezer but think that has something to do with it. Water in a boat would not be quick cooled
  14. alldodge

    Gas leak gas freezeing

    Would like to see that experiment Its 40 now, was it colder prior to finding it? Probably has some oil mixed
  15. alldodge

    Gas leak gas freezeing

    Agree, its not gas, and wander what it is, water freezes at 32* not 40
  16. alldodge

    5.7 Venturi Cluster

    There is a different float setting for a solid and spring loaded needle valve
  17. alldodge

    Oil coming from exhaust riser rubber coupling

    Sounds like there was an issue, and with oil coming out the exhaust, it either has a cracked head, piston or block Do a compression test, but for the most part it does appear you will need to rebuild or replace
  18. alldodge

    Oil coming from exhaust riser rubber coupling

    What motor, and serial numbers are best? This is a new problem, as in the motor could reach WOT before? Check the oil and is it low now? Any water in the oil, milk looking?
  19. alldodge

    Toilet Installation Mishap . . .

    I don't know anything that can glue it back on and hold. Suggest fab an aluminum plate to fasten to all 3 bolts Also suggest when installing next, the tank doesn't need to be real tight (Just replaced 2 my self last year in rental, American Standard Champion-4, only one with 4 inch flush valve)...
  20. alldodge

    Rub Rail Restoration??

    Rivets 1/4 inch, screws will be unable to handle the vibration unless maybe their used with lock nuts IMO that is
Top