Search results

  1. R

    Can't get flywheel off!!

    You should never have to resort to heating these expensive parts !!----Get a hefty puller.-----Cheaper than damaging parts under the flywheel !
  2. R

    3 HP Evinrude fuel supply problem

    Looks to be a 62 model.-----Check the fuel filter in the tank outlet.--------try-----evinrudeparts.ca----Possibly they can help.
  3. R

    1994 OMC 115hp turbojet 115JEER

    Rod caps will only fit on one rod.-----Easy to figure out which cap fits that one rod.-----What is your location in Canada ?-----
  4. R

    1994 OMC 115hp turbojet 115JEER

    Now you know why it was for sale.------This damage is very typical on the V-4 crossflow engines.----All of them will suffer this fate !-----Amazing how well they run on 3 cylinders until the second piston goes poooff.----What do crankshaft and rods look like ?
  5. R

    1979 1150 thunderbolt merc drive shaft

    Put driveshaft in a hefty vice.----Use 2X4 to protect gear housing. and give it a bump with a hefty hammer.---As stated I can not see what you are doing !
  6. R

    Can't get flywheel off!!

    One bolt flew away like a little bird he said.
  7. R

    Can't get flywheel off!!

    That puller may be too flimsy / bendy.----You are tightening the 3 bolts and then giving the center bolt a bump with a hefty ball peen hammer ?
  8. R

    1979 1150 thunderbolt merc drive shaft

    I am not there looking over your shoulder.----There is a nut on the bottom of the driveshaft , is that off ?
  9. R

    Mercury 135 Blackmax

    The crankshaft has sealing rings on it.-----Look like a big piston ring.----Separates the 6 crankcases.-----Johnson / Evinrude used those from 1958 to last year when production stopped.
  10. R

    2001 Johnson 25 hp starting problems

    In neutral turn tiller to the neutral stop.----Ignore START mark on handle.-----Pump carburetor full with manual fuel pump on the hose.-----Operate primer pump full out and full in 3 times.----This pump pull fuel from carburetor bowl and sprays it into the motor , bypassing the...
  11. R

    9.8 Running on One Cylinder Only

    So does one trigger coil fire both cylinders ??
  12. R

    1977 Johnson 70 Horse Salvageable?

    Have to ask-----Any plastic needle cages on those 2 split main bearings ?----What do those journals look like ?
  13. R

    2001 Johnson 25 hp starting problems

    2 or 3 cylinder ?----Model #.
  14. R

    Mercury 135 Blackmax

    Remove one of the drain plugs on the middle carburetor.----Operate manual fuel pump.----Gas should pour out.----Running with a blocked carburetor will starve 2 cylinders of gas and OIL.----So do the compression test again.
  15. R

    Top cylinder not firing Johnson 55ESL69A

    Low speed mixture screws are set at how many turns out from gently seated ?
  16. R

    Help! Need advise!

    Round of applause for above post #8
  17. R

    1973 Chrysler 6 HP Two Stroke

    Chrysler became Force-----Bought by --Brunswick Corporation ( Mercury Marine)-----So your local MERCURY dealer might be able to help if you show the part numbers for the 76 model.----Failing that any bearing shop can measure seals and come up with a match.---Measure seals / housings /...
  18. R

    1989 Johnson 90horse VRO issues

    The VRO pump runs off PRESSURE pulses from the crankcase.----The wiring is just for the " no oil " alarm.----If you premix in your tank there is no need for this electronic module.----Best option is per post #3
  19. R

    Johnson 70 hp 3 cyl / 2-stroke dies when giving more throttle

    See post #4 ?----And who cleaned the carburetors ?----Does spark jump a gap of 3/8" on a test device , yes or no ?
  20. R

    1989 Johnson 90horse VRO issues

    The elegant / simple thing to do is to mount a 2 nipple pump.----This pump mounts directly over the pulse port on the intake manifold.----Leaving the VRO unplugged has no effect on starting.
Top