Search results

  1. alldodge

    Hardin bravoitis kit install

    I would assume the brass brush would be used to clean the hole out, using a drill. The hose is inserted into the bell housing, then the plastic piece is inserted using the tool with a 3/8 extension. I have never used silicone on these parts. silicone will cause them to slide even when dry...
  2. alldodge

    Bravo 3 Trim sender

    The Org/Blue goes to the 10 pin connector (Analog) The Org/White goes to connecter B-13 (Digital) Black is ground Here is a short vid on connecting to smartcraft monitor That said your using analog gauges with smartcarft monitor. To use analog gauges I think your going to need to get a...
  3. alldodge

    08 350 Mag MPI: No Spark & Negative Turning Tach While Cranking. Banging My Head Against The Wall

    Are you getting 12V at the coil Pink/Wht pin C-A ?
  4. alldodge

    Parallel Batteries to Solenoid

    Yes there are marine rated solenoids and they "look" just like the one installed. My Formula has two of them, one for combining batteries, and one to operate the wench. They are rated for continuous duty, but they never are turned on and left on. Google 24213-BX The battery one should be...
  5. alldodge

    Parallel Batteries to Solenoid

    The solenoid is used to combine the batteries together if the one battery will not start the motor. My formula uses the same thing, and there is a switch up by the key switch that is pressed if needed. The solenoid is an easier way to combine and is momentary where a battery switch is done...
  6. alldodge

    Hull Supports?

    The box is there to transfer the load over a wider area. It needs support from one side to the other to keep the boat from squeezing together. When filled with foam it becomes more ridged. If you just went straight across in front of the tank then there is just two points to hold the sides...
  7. alldodge

    Little help, I'm stuck on the water.

    If your talking about parts in item 14, this is the needle seat assembly. If that is the case it needs cleaned out real good and replaced
  8. alldodge

    Little help, I'm stuck on the water.

    The vid is showing me that your flooding, and is caused by curd in the needle seat or the float sank, my guess is crud. The best method to fix temporary, is remove the top of the carb, should be 7 screws. Then remove float and needle, clean out then reinstall. Another possible option is pump...
  9. alldodge

    Trim sensor wiring

    OK then yours would be like this The limit is on the port side and the gauge is on starboard. It doesn't matter which of the black wires coming from the limit or sender is connected to which other wire.
  10. alldodge

    Trim sensor wiring

    Being a 1988 I'm thinking you have two solenoids, so here is the diagram If you have only one solenoid let us know Edit: woops you said two solenoid in first post
  11. alldodge

    1989 waverunner 500 water in cylinders

    Your not going to suck water in from the exhaust with a 2-stroke. The read valves allow air and fuel mix to be drawn thru the intake, around the crankshaft (to lube crank) then up into the cylinder to burn. The burn gases are expelled when the cylinder starts back down. Your water can be...
  12. alldodge

    Steering

    Is this a single cable system or dual cable system? If its a single cable helm then just route the cable which goes around the other way
  13. alldodge

    Change to High Volume Oil Filtration

    The sender came with some adapters so the install will be easy. The filter housing has two inlets so remove the one not being used (arrow pointing in). The plug was tuff getting out, had to use an extension. Then install sender without pipe dope (need a good ground) Then installed new...
  14. alldodge

    Change to High Volume Oil Filtration

    Got the manifold installed, only issue other then being hard to get at, was hoping the center O-ring stayed in the right spot. If it didn't there will be a mess when its fired back up in the spring. Fittings on the filter housing Fittings removed from housing and oil cooler These items...
  15. alldodge

    Change to High Volume Oil Filtration

    Managed to get it off The manifold will use two 5/16 Hex head screws to secure. The output port is lined up with the outer hole next to the block. Two O-rings are used to seal it. My plan is to drill and tap for a temp sender on the input side of the remove filter housing. Will post more...
  16. alldodge

    Change to High Volume Oil Filtration

    For those that remember or find my threads on my repower, please don't mention the builders name. This is just documenting my changes and things I found out on OSO and another member. Had an oil leak on one of my hoses for my remote filter setup, between the cooler and manifold head unit, so...
  17. alldodge

    Weight distribution / replacing bunkboards

    A bunk trailer should have center rollers if the keel of the hull may come in contact with the cross frame when being loaded. The rollers are different then the ones used to support the keel, they are still strong enough support the load while loading or off loading. Once the boat is resting...
  18. alldodge

    470 mercruiser rebuilt engine install questions

    Can use the manual or the electric.
  19. alldodge

    Volvo DP-SM gimbal bearing issues

    My guess (not a VP guy) is there is more grease coming out this location because this is where the grease fitting tube meats the entry hole in the gimbal bearing. It isn't coming out the other side as much because its leaking out before it gets over there. This is not an issue, and is normal...
  20. alldodge

    Thermostat Housing Replacement - 1993 7.4L/Bravo 1

    This is what you have now. It has hoses connected to the top elbows and bottom manifolds. The two hoses with arrows are removed. Once removed the openings are plugged. If you have screw in fittings, just remove fittings and install pipe plugs. If it is part of the elbow, then use item 12...
Top