Search results

  1. R

    1997 johnson 175 faststrike powerhead ?

    The gasket between block and exhaust housing is different.----You have a 200 HP 90 degree motor on the boat.------Are all carburetors on the front of the block ?------Are carburetors neatly in a row on both sides of the block?------Pictures make this elegantly easy to identify.----I say a 200 HP...
  2. R

    New aluminum prop rubs slightly

    Make one.
  3. R

    Evinrude tilt and trim.

    Agreed the 77 model is shown with the external trim / tilt cylinders.----This forum should require pictures / model numbers before questions are allowed to be posted.
  4. R

    Evinrude tilt and trim.

    I assumed it was the more common 2 cylinder motor.----The OP might have a 3 cylinder model.;-----That is why the model # MUST be posted here.
  5. R

    Prop shaft help

    See if you can give it a bump to turn it , to loosen the corrosion.----No it is not threaded.
  6. R

    1996 Johnson 50hp retaining screw for pinion gear.

    No that has nothing to do with the pinion gear.-----That is the pivot pin for the shifter fork.-------Likely the thread inside is stripped.------This will require major work.---Might as well take it apart and see if your local machine shop can help you.-----Or used housing.----There is also a...
  7. R

    Evinrude tilt and trim.

    It will be interesting if you can pull this project off.----None of these parts will interchange without welding / machining.-------Then that single cylinder may not have enough oomph to trim the 85 HP.
  8. R

    91 mercury 115 flooded then no spark

    Step #1 is to load test the battery even if you bought it last week.----Then pull the starter apart for inspection and OHM test on armature.
  9. R

    Hydro swift new owner

    Do a COMPLETE inspection of the boat first.-----If wood was used in the structural parts it may all be rotten.------Don't spend any coins on cosmetics / seats / paint until the boat is declared safe and sound.----Paint is your last worry.
  10. R

    Driveshaft bearing race

    Sorry-----It is a simple job to remove a bearing like that.----Hard to explain years of experience in one minute.
  11. R

    Driveshaft bearing race

    The bearing is shown as a separate piece.-------So use your grinder , weaken it and remove it from the shaft.-------And have a very good look at your gears considering that bearing was shot !!!
  12. R

    91 mercury 115 flooded then no spark

    That is why the poster should put up serial # or pictures.----I agree a 1991 inline 6 might be rare in North America.
  13. R

    '89 Johnson 60HP overheating

    Well----1990 might have been the first year for slow on them.----Trouble shoot the cooling system first.
  14. R

    Intermittent "cough" during startup.

    Would it have anything to do with the fact that at the bottom of the piston stroke the crankcase is open to the exhaust housing ?
  15. R

    Weep Hole ??

    Pressure test the gearcase.
  16. R

    1984 johnson 90hp carb leaking fuel out air cleaner

    Warm it up with a wee propane torch and it will fall off !
  17. R

    Intermittent "cough" during startup.

    Force power-----Do you understand why these 2 strokes sneeze when set too lean on idle mixture ?
  18. R

    Intermittent "cough" during startup.

    That is why when an engine is " flooded " there is too much fuel in the air mix.----Even though there is spark it simply will not ignite.------
  19. R

    Intermittent "cough" during startup.

    You could start learning by searching for -----LEL gasoline-----Using google.
  20. R

    1997 johnson 175 faststrike powerhead ?

    Hard to say what was done without pictures.-----What is maximum HP rating for the boat.-----Sounds like the entire motor was replaced.
Top