Search results

  1. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    I installed the new water/fuel pump assembly and she started right up, I guess pouring gas down the carb didn't work too well. So I did the static timing at 0 and the computer should automatically adjust the base timing and timing advance? No need to time anything with a timing light?
  2. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    Ok I just re-did the timing from scratch and now it seems to want to start and it'll puff puff a couple of times but won't fully run, but at least no backfire anymore. Just to confirm I did the procedure correctly, here's what I did: 1) Set Cylinder #1 to TDC Compression, I used a scope in the...
  3. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    I'm pretty sure it should be TDC compression, I turned the engine over until I could feel air blowing out cyl #1 then turned it manually until the piston was at the top, if I was 180 out would the timing mark still line up on the crank pulley?
  4. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    I'm waiting for my new water/fuel pump assembly since the pulley on the old one was really tight but I just tried pouring some gas straight down the carb and it's not starting, seems to actually be backfiring through the carb a bit, not sure if it's because the boat is parked facing uphill so...
  5. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    Ok so just to confirm this is what I did, set #1 on TDC compression, the mark on the crank lines up with the 0 on the timing plate, I installed the distributor cover so that the rotor points to #1. Is that it and the computer takes care of the rest or do I run the motor at idle and then set it...
  6. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    https://www.perfprotech.com/mercury-marine-parts-catalog/wiring-harnesselectricalmounted-on-exhaust-elbowtb-iv/assembly/1621/70?model=418 That's the diagram for my engine, the wires go to #9 which says it's an ignition module kit. What do you mean by flat cap? I have #1 set to TDC compression...
  7. CLi87

    How to do new distributor timing on Mercruiser 7.4 Gen V?

    I'm trying to reinstall a distributor and didn't mark the old one, what is the procedure for new distributor timing for a Merc 7.4 Gen V? I tried to look up some guides and they mention putting it in base timing mode either by shorting the purp wire or jumping the two white wires, but on my...
  8. CLi87

    Can I use slightly longer push rods than stock on 454 Gen V?

    Wait my motor is a Gen IV? I thought 93's were Gen V? and I have the flat torque rockers, no adjustment nut, I thought that was a Gen V feature?
  9. CLi87

    Can I use slightly longer push rods than stock on 454 Gen V?

    Are they not the same part #? https://www.perfprotech.com/mercury-marine-parts-catalog/cylinder-head-and-rocker-cover74l-bravo/assembly/1621/180?model=418 That's the parts diagram for my Gen V by serial # and it shows part #75589 and #75590...
  10. CLi87

    Can I use slightly longer push rods than stock on 454 Gen V?

    No, I'm rebuilding the top end of my Gen V
  11. CLi87

    Can I use slightly longer push rods than stock on 454 Gen V?

    So I had several bent push rods due to seized valves so I bought a full set on ebay that supposedly came from an 89 454, which should be the exact same push rod as the part #'s are the same for the push rods between the 89 454 and my 93 454 Gen V, but upon examination both the intake and exhaust...
  12. CLi87

    What is this guard around the valve spring?

    I actually just re-used the original ones, they were in good shape and the engine only had 8 hours on it, but had been sitting for 25 years. Do you have a link to the improved seals you're referring to?
  13. CLi87

    What is this guard around the valve spring?

    The valve rotators are the spinning part on the bottom of the valve, but can I just leave the oil control sleeve off? They're a real pita to install, it seems like their purpose is...well oil control? It seems in this engine there's not really any valve stem seal, just a plastic cover really so...
  14. CLi87

    Are all Mercruiser 3.0 front sump oil pans the same?

    Does it matter if it's a 2 piece RMS or 1 piece RMS? Same pan?
  15. CLi87

    What is this guard around the valve spring?

    Very interesting, I've never seen them before, is it a big deal to leave the rotators off?
  16. CLi87

    What is this guard around the valve spring?

    Do I need to have these? It was a pain to remove and looking like a worse pain to reinstall and it's not on the parts diagram breakdown for my engine
  17. CLi87

    What is this guard around the valve spring?

    Oops, sorry, forgot to attach the pic
  18. CLi87

    What is this guard around the valve spring?

    I'm rebuilding the cylinder head on a Merc 7.4 and was wondering if anyone knows what these metal guard things are around the valve spring? I don't see them in the parts diagram either.
  19. CLi87

    Are all Mercruiser 3.0 front sump oil pans the same?

    The bottom of my oil pan is rusted and I'm looking to replace it and was wondering if all of the front sump oil pans are the same between years? Mine is a 2007 Merc 3.0 TKS
  20. CLi87

    Mercruiser 7.4 Starter Grinding/Partial Engagement?

    I ended up drilling the hole out larger and tapping it and then putting an E-Z Lok threaded insert in.
Top