Search results

  1. C

    Horn Constantly Blows When Battery Switch Is Turned On?

    Probably a bad switch
  2. C

    Keeping pontoon gates open

    Learn to ride with them closed? I don't think I would get more enjoyment out of my pontoon by leaving the doors open? I can see over the doors unless I'm riding on the floor I guess?? But who knows different strokes for different folks, people get their kicks out of all kinds of different things?
  3. C

    1992 Johnson 48spl lower unit.

    The new replacement plugs (at least on the 25hp I'm working on) I have seen have an Allen head recessed in them they are easier to get a good purchase and remove those then the old slotted ones for sure.
  4. C

    Twin 2.6 omc outboards

    Are you sure the kill circuit is ok. Maybe disconnect the black yellow wire to rule out the ignition switch or kill switch? Just throwing out random thoughts. It would be really weird that it would cut off and start right back up, you would think everynow n then you would get a time it might not...
  5. C

    1983 evinrude 35hp shift rod connector

    I bet you can buy one on eBay.
  6. C

    1977 6 hp johnson waterpump

    Are you sure you put the key way or pin or whatever drives the impellor on that model in place.
  7. C

    Low rpm at wot

    Are all the carb butterflies opening? Are you sure your not sucking air in the fuel line? Does pumping the primer ball make any change? Fuel filter plugged? Have you hooked a little rest light or clamp on meter or timing light to confirm at throttle that each cylinder is indeed fireing?
  8. C

    50 hp OMC triple vibration at lower rpm

    I can't say for sure but I would put money on that they are the same flywheel. To confirm this look up each flywheel on your favorite parts website and see if it's the same part number? But yes if you have a plug wire without continuity that for sure will give you poor performance cause that...
  9. C

    1992 Johnson 48spl lower unit.

    Yes its 80w90. Best to use a marine oil it has additives that allow it to suck up more moisture and hold it in suspension if you have leaks. Get an impact screwdriver. It's the easiest way to get those stuck plugs out. You can buy them off Amazon for $10;if your or a busy don't have one. You...
  10. C

    Johnson 50hp 1995 - constant beep at power up

    Is it a low oil sensor....was something not defeated or bypassed correctly with that system?
  11. C

    Why can't I find this part?

    It's not on that page, you need to go to the exhaust housing page usually.
  12. C

    50 hp OMC triple vibration at lower rpm

    Clunking isn't normal but that's about all I would think you would get out of a deep V 16' fiberglass boat with a 50 on it. Are you sure the lower unit is ok...clunking normally comes from there.
  13. C

    50 hp OMC triple vibration at lower rpm

    Post the video on YouTube then post the link address here. The forum software will embed it in the post. If you have a Google account you basically just have to sign in to YouTube and just hit the upload button and select it. You can make it a private video if you want where only people with the...
  14. C

    Why can't I find this part?

    Have you looked up your engine on any of the parts sites that pave the parts diagram? They don't offer one? If not take the part number and go to eBay and put it in and see if you can buy a used one.
  15. C

    2 stroke 70 hp that hesitates at acceleration

    Have you cleaned the carbs? Are you sure you have spark on all cylinders?
  16. C

    Lower unit seal

    Ok I just looked at your diagram, yes that is your thrust washer/bushing as it calls it. It should just be on the prop shaft behind the propeller
  17. C

    Lower unit seal

    Did a thrust washer come off behind the prop? There usually is one back there. Without looking at the parts breakdown I can't say for sure what it is cause I don't know. It also could be a seal retainer or just something to protect the seal there. Now you have me wondering I'll look it up.
  18. C

    OMC specialty products for carb rebuilds?

    Well OMC ceased to exist 20 years ago. But I believe that you mean Bombardier dropped the Evinrude name. But Bombardier still has parts for some stuff. But yea for all your suggestions will work. Screw drivers that fit an orfice tight or custom ground will work. Whatever pair or primer that you...
  19. C

    Lower unit seal

    I believe that's your thrust washer. If your holding 10 pounds , that's a lot, I don't think your leaking. The fishing line could of got between the shaft and seal at one point and let the water in or maybe it could just be moisture from condensation in a small void for a long time? If it...
  20. C

    1984 Evinrude 25hp mounting

    I was thinking that his pictures were just for mockup. And he was going to do something more permanent and secure. At least that's my take and what I thought he had planned!
Top