Search results

  1. alldodge

    Mercruiser shifter

    Maybe but.....
  2. alldodge

    Lenco joystick/dual prop electric

    My guess is the Bat's used to power tabs are not the Bats that would be used for trolling. Need a voltmeter and trace the connections
  3. alldodge

    Mercruiser shifter

    The Alpha drive uses a shift interrupter on the shift plate to unload the clutch to be able to shift out of gear and into neutral. You need to check the connections and then if needed adjust the interrupter Need your serial number or at least what year?
  4. alldodge

    Lenco joystick/dual prop electric

    Here is the manual https://www.absolutemarine.co.nz/image/catalog/documents/Lenco/OwnersManual.pdf
  5. alldodge

    Lenco joystick/dual prop electric

    Looks like you have Lenco Troll'N Tabs, where there is a trolling motor attached to each trim tab I moved your thread and merged the two threads Don't start multiple threads in different areas
  6. alldodge

    Brass block drain plug leaking like a sieve

    NPT does not have chasers To clean threads the tap just goes in and back out. Once it makes contact with all threads, the more it's turned the larger the hole is made. No issue with going a tad larger, just don't do more then maybe a 1/4 turn or so
  7. alldodge

    Engine Alarm / Wiring Diagram 2003 5.7GXI-D

    The alarm is behind the helm You should here a beep when key is first turned ON This is a V6 but same as V8
  8. alldodge

    Anyone try this scan tool?

    Also it's a subscription tool, so have to pay every year to keep it working Rinda will be cheaper in the long run and it works on all most everything, but does use different adapters
  9. alldodge

    Brush replacement

    If you can find a electric motor repair shop like for starts/alternators, they may have the brushes
  10. alldodge

    1991 Monterey 189 SCR Owners Manual

    That is manual 14 Search for Mercruiser manual 14 or 8M0065951
  11. alldodge

    Brass block drain plug leaking like a sieve

    Like ESG there is something wrong in what you have tried The block drain is a NPT (national pipe thread) which means it is tapered thread, not straight. While thread sealant is very helpful, it's not absolutely needed with a cast iron block and brass plug What tap did you use and what plug?
  12. alldodge

    4.3L Carb Mercrusier Auxiliary Heater

    Don't think that will work, that's more for raw cool water coming in from the pump. Biggest issue I'm having is finding a cut away view of you thermostat housing which is HERE and it's the pic on top. The sensor on top is and is actually in behind a section in the housing so it sits in the...
  13. alldodge

    Mercruiser 120 Fuel Help

    Disconnect the throttle cable at the carb and move it by hand at the carb
  14. alldodge

    Mercruiser 120 Fuel Help

    When throttle is pushed down do you see fuel squirt down throat of carb? If not, Disconnect fuel line at carb and see if it pumps fuel into a container How old is the gas
  15. alldodge

    Base timing on TB5 350 V8 Carbureted with knock Sensor???

    No,
  16. alldodge

    I am starting to believe some of the global warming in N J.

    I hope you guys had fun but it's run it's course Closed
  17. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Chainsaw will make quick work of that :oops:
  18. alldodge

    I am starting to believe some of the global warming in N J.

    Simmer down No bias no more then anyone else here voicing what they are seeing and reading. Anyone can find all the facts needed to fit what they believe, same as religion In Jan 1902 Scott arrived in Antarctica and setup a command. There is a small structure there (Scott's Hut) he used, which...
  19. alldodge

    Fuel outlet connection on Cool Fuel 2

    Got it see post 4
  20. alldodge

    Fuel outlet connection on Cool Fuel 2

    Thanks If there isn't any burrs inside were the quad ring goes it will seal. I had fist Gen cool fuel which used 2 O-rings and the same screw, and only thing to watch for is make sure the screw goes in the correct place on the tube. The screw can be placed in the groove but also before and...
Top