Search results

  1. jerryjerry05

    1984 force 125 spark issue

    Is the stator new? CDI stators can read lower than OEM. Borrow/buy another meter and see if that makes a difference? Lots of times, if theres any type reading it can be good
  2. jerryjerry05

    1984 force 125 trigger help?

    Google this: "male pin for wire connection" A whole bunch of different parts show up, yours is one of them
  3. jerryjerry05

    Starter Bendix stuck

    I had a bunch of Force outboards, I NEVER bought a new starter in 30 years. Always rebuilt them. How ever I did buy the expensive rebuild kits from Mercury.
  4. jerryjerry05

    1998 Force 120 Stalls out in Low Gear

    Mercury uses a 5/16" hose and older Force used 1/4" If your going to pull the pickup?? Be very CAREFUL as those fittings aren't meant to come out easily and can be damaged. The best way to check the pickup is to empty the tank and then remove the sending unit and then you can see inside the...
  5. jerryjerry05

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    If it only does it when you prime the system?? Not sure I'd worry too much about it. When you squeeze the ball your putting the system under a lot of pressure. The fuel pump is a real low pressure system 2-4# (if that?). Make sure the screw/screws holding the bowl on are tight.
  6. jerryjerry05

    Force 50 priming solenoid

    Yes normal.
  7. jerryjerry05

    Chrysler 55 one cylinder occasionally fires

    The following is my opinion: Seafoam is a waste of $$$ Get a can of spray cleaner and use it to clean the carb. I bought a can of SF tried to use it to clean the carbon from the piston I had setting around. DID NOTHING!!
  8. jerryjerry05

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    The "robber" seal is for a different motor. :) The kit covers a bunch of motors, it might cover 20-50 different ones. That rubber seal fits a Mercury motor.
  9. jerryjerry05

    1990 force 125 shift bellow leak

    120 any countries currency to save an outdrive is well worth it. Oh yea, THANKS
  10. jerryjerry05

    1990 Force 120HP trim and tilt not keeping motor up no leaks

    Yea looks broken(never saw that before) fix? a thick glue will cause problems, superglue is probably the way to go??OH OH too late. Gas from the top carb: needle seat needs replaced.
  11. jerryjerry05

    1998 Force 120 Stalls out in Low Gear

    Temp/overheat-gauges or alarms? The thing about a gauge is you don't watch them all the time, if you do? Myself, I'd get seasick. Fix is a louder horn, car or motorcycle horn and put where you can see/hear them. A pressure gauge just tells you it's pumping but won't say anything if it quits...
  12. jerryjerry05

    1990 force 125 shift bellow leak

    Can you tell us how much$$$
  13. jerryjerry05

    1990 force 125 shift bellow leak

    OR!! look for a replacement drive?? Yea, one of the WORST!! design/engineered things in the entire marine field. :(
  14. jerryjerry05

    Chrysler 55 one cylinder occasionally fires

    Jimmbo, I agree completely, I use a torque wrench to tighten lug nuts. Just about everytime I do a brake job I have to use a hot wrench to loosen the lugs that were installed by an impact wrench. No way would the people get them off with just a 4 way.
  15. jerryjerry05

    Chrysler 55 one cylinder occasionally fires

    Get an impact wrench. Then you won't need to hold the flywheel.
  16. jerryjerry05

    1997 Force 90hp Stiff steering

    If someone's gone through all that trouble to fix it before? Not so sure it's going to FIX?? Maybe find another motor and change the powerhead? or get a different motor all together?? You said: "The bottom of king pin is rotted as well and retaining ring is sitting on lower unit. Also the lower...
  17. jerryjerry05

    Force 120 (~1998) starter mounting bracket wear

    From what I see?? is the bottom mounting bracket still in place? #14
  18. jerryjerry05

    IR Laser Thermometer

    Mine also sets in the tool box and I unhook the battery(just in case)
  19. jerryjerry05

    1997 Force 90hp Stiff steering

    How about some pics of the zerks and the rotted area?
  20. jerryjerry05

    IR Laser Thermometer

    Try online ordering. They're pretty good about getting it there.
Top