Search results

  1. jerryjerry05

    1987 Force 50 Model B

    That is a points system. File the points before you do anything else. That one coil(white/top) shows that it might be a problem. Those coils are fairly expensive.
  2. jerryjerry05

    1990 force problems

    Standard magneto has coils, new and cheap. http://standardmagneto.com/marine.html Try swapping the coils around to see if that makes them spark??
  3. jerryjerry05

    1987 Force 50 Model B

    If the lanyard is not hooked up?? then it shouldn't fire. How about pics of the coils and the sides and top of the motor??
  4. jerryjerry05

    1987 Force 50 Model B

    The 87 B came with points. Maybe someone changed things around? Make sure they are clean and making a good contact. That motor might have a kill switch in the system.
  5. jerryjerry05

    1987 Force 50 Model B

    outboardignitiondotcom has test procedures for your motor. Just replacing the stator might help then again might not??? Check for broken wires and terminals, especially inside the plastic plug-in connectors. We recommend that you remove the pins from the connectors and visually inspect them...
  6. jerryjerry05

    1990 50HP Force Starts but won’t stay running

    Cold or hot shouldn't make much difference. You remove both plugs when doing the test? They sell snake camera's for most new phones, 16$ ebay Get pics of the bore from the low cylinder. Might just be a bad head gasket????
  7. jerryjerry05

    1990 50HP Force Starts but won’t stay running

    Welcome!!!! Sounds like the floats not set right or the needle is locked in place(closed), take the carb apart and check the floats level. There's a bunch of things that can help in the first few posts in this forum. Read them and see if you can find how to set the float??
  8. jerryjerry05

    Hard to start and no idle

    No luck on the manual. Try ebay
  9. jerryjerry05

    Force 85 1989 flywheel magnet pain

    That flywheel and ignition is from a lot newer motor.94-99 Someone changed it over?? Pics of the gear housing?
  10. jerryjerry05

    Chrysler engine overheating

    The old impeller, did it come out complete? or were the vanes missing? Missing vanes, they get to the bottom of the motor and clog there and that causes an overheat?? Drop the lower unit, hook a hose direct to the tube to the motor. Turn it on and start it and see if it gets hot then. No?? then...
  11. jerryjerry05

    1990 Force 50 HP Bearing Cage Kit Replacement

    Nordins right, the shredded rubber is the driveshaft cover that fits on the end of the shaft. Grease the splines but no grease on the end of the shaft. You said" I took a few pictures. It looks like that rubber seal came from the drive shaft under the water pump. There's a spring showing where...
  12. jerryjerry05

    1990 Force 90Hp (906x90c) lower unit questions

    Try Franz Marine
  13. jerryjerry05

    1995 70HP Force, cranks but wont fire.

    U-TUBE VIDEO'S Look on the net for specific tests. There's a bunch of compression test video's. The first 4or5 posts in the Force forum has tests and tips for your motor. I'd stop and go through each one, might be something you need in one of the posts???? If you can't figure it out? then ask...
  14. jerryjerry05

    1990 force problems

    Usually 60-70 on the bottom 2, could be just a bad head gasket. Take the head off, BE VERY CAREFUL WHEN REMOVING THE BOLTS!!!! They've been there for maybe 30+ years and they tend to get stuck and break off. PB Blaster, a propane torch and patience, patience, patience!!! One time it took me...
  15. jerryjerry05

    Chrysler engine overheating

    It's a 1976 You running on the hose,muffs or bucket? The bucket needs to be real deep, 4-6 inches over the cavitation plate. The older motors needed a special muff, need pics of the water pickup on the lower unit. If you have the 2 piece lower? then you need a special muff.
  16. jerryjerry05

    1990 Force 50 HP Bearing Cage Kit Replacement

    Better pic of the rubber washer thingy?? Where does it fit?
  17. jerryjerry05

    1990 force problems

    Compression test, spark test. The video sounds like it's running on 2cyl. How much oil you adding to the gas?
  18. jerryjerry05

    1995 70HP Force, cranks but wont fire.

    Compression, spark, fuel. Roscoe says check the fuel pump diaphragm, along those lines, check the primer for a bad diaphragm (pinch off the hose from the primer to the carb).
  19. jerryjerry05

    1989 Force 50hp spark plug options

    Yes, just unscrew the black connectors and switch them around. Change the plug wires too.
  20. jerryjerry05

    1989 Force 50hp spark plug options

    Before you buy!!! try swapping the coils around and see if the weak spark changes when you swap them. In all my years, I've only seen 1-2 bad coils
Top